How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-0385
IC Name: MCP23017 Package/Case: DIP-28
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. RoboticsBD Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-0919
Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-1421
3S 11.1V 12.6V 20A 18650 lithium battery protection board (comes with recovery function-AUTO Recovery). Application: Nominal voltage of 3.6V, 3.7V lithium battery (including 18650.26650, a polymer lithium battery). Continuous discharge current (upper limit): 20A (if the cooling environment is not good, please reduce the load current use). Continuous...
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-1870
Compatible with 3.3V and 5.0V power supply. Compatible with 3.3V and 5.0V signal. Semi-hole pads, onboard module, thin PCB, having a thickness of 0.8mm. Has RXD, TXD signal indicator light, monitor send and receive status.
Reference: RBD-1754
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-0576
Chipboard STM32F103C8T6 On board, SWIM interface and reset button Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V. Power light and the Demo indicator light Leads all the pins and has detailed label for the Pins. Support SWIM debug mode. RoboticsBD
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1771
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-0439
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....
Reference: RBD-1781
1. Micro USB ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 16 x 14 mm .
Reference: RBD-1782
1. USB Type B Female ( 5pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 20 x 20 mm .
Reference: RBD-1783
1. USB Type A Male ( 4pin, A type, Male connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 32 x 15 mm .
Reference: RBD-1784
1. USB2.0 Type A Female ( 4pin, A type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 22 x 17 mm .
Reference: RBD-1785
1. USB3.0 Type A Female ( 9pin, B type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 28 x 25 mm .
Reference: RBD-1786
1. USB Type C Female ( 13pin, C type, female connector ) 2. Base Material: FR4. 3. Board Thickness: 1.6mm. 4. Size: 40 x 25 mm .
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5V Speaker Load: 2-8 Ohms Input and Output Connectors: Pins on 0.2" centers Size: 24 x 23 x 105 mm (L x W x H) Net weight: 3g
Reference: RBD-1953
Input Voltage:DC 4.5-24V Module Size: 10 x 20 mm Adjustable Range:0.8-17V,fixed voltage (1.8V 2.5V 3.3V 5V 9V 12V) Output Current:3A (max),actual testing input 12V output 1.5A Transform Efficiency:97.5%(max) (6.5 to 5V 0.7A) Switch Frequency:500KHz Output Ripple Wave:20mV (12V to 5V 3A) 20m band width
Reference: RBD-2150
Type: Voltage Regulator Operating Temperature: -40-+85 Supply Voltage: 60v Dissipation Power: 10A Package: SMD
Reference: RBD-2173
High current 3A charging board for Type-C USB input Adjustable charging current through resistance adjustment Optional cut-off voltage of 4.2V or 4.35V Efficient working effects with a polymer ternary lithium battery Note: No power indicator or battery protection function included
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1367
RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing Working voltage: 5V LED drive mode: Common cathode driver
Reference: RBD-1368
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
