Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0369
Brand: SparkFun Electronics
Supports binding and multicasting for home automation Mesh-network topology 2.4 GHz for worldwide deployment Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board Firmware upgrades via UART, SPI or over the air TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC DATA RATE: 250kbps Max RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile...
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-0284
Gain: 2.0dBi-2.5dBi Antenna connector: RP-SMA Male Connector Standing wave ratio(SWR): <1.5 Weight: TxA10.3g, RxA 11.5g TxA is a circular-polarized Omni antenna with three lobes RxA is a circular-polarized Omni antenna with four lobes
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-0440
433MHz operation Ultra-low power consumption (3.5mA or 22mA depending on mode) with sleep option (80μA). 10dBm output power and high sensitivity providing long range in the open environment. 3V-6V operating voltage. Serial pass-through mode to replace the serial cable (half duplex). IO pass-through modes. RoboticsBD
Reference: RBD-0436
Supply Voltage: 12V Standard interfaces (as that of the extruder) Reserved GCI like I2C and RS232 3 MOSFET’s are applied to the heater/ fan and thermistor circuit. Another 5A added to protect the component parts. An 11A fuse is added to the hotbed. Support 5 stepper drive board
Reference: RBD-0435
Supply Voltage : 8-35 VDC. Current : 1.0A (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.
Reference: RBD-0565
Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software. USB power supply and peripherals power phase are separate to protect computer security. All the signals are to-isolate which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc. Wide input voltage range: 12-24V, and with...
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-1604
Supports Digital terrestrial video and radio program recording (records digital terrestrial TV on PC or Laptop). The included Input Terrestrial Antenna will offer stable TV signal. Supports Real Time digital video recording and broadcasting. Supports Watching DVB-T digital TV and listen to DAB and FM radio. Full DVB-T bandwidth reception (at 6 / 7 /...
Reference: RBD-1722
Antenna Size : approx. 26 x 26 x 9 (LxWxH) mm. Module Size : approx. 26 x 36 x 4 (LxWxH) mm. Net weight : approx. 16 gm. Gross weight : approx. 17 gm. Mounting : approx. 3 mm. The default baud rate : 9600.
Reference: RBD-2016
Backward compatible with USB 2.0 USS, MDIX support Jumbo packets up to 9 KB Plug and play installation Full-duplex and half-duplex operation of fast ethernet Suspend mode and remote wake up via links and magic packs
Reference: RBD-2136
Very Few External Components Excellent Receiver Sensitivity and Robustness to Interference. Programmable Output Power Up to 4.5 dBm. High-Quality Construction