Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-2199
Compatible with the Arduino IDE, making it easy for beginners to start using Smaller and cheaper than traditional Arduino boards Powered by a 16.0 MHz microcontroller Fully assembled except for headers, allowing for easy soldering Great for projects where size and cost are a concern Perfect for beginners to jump into electronics Can be used for a variety...
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-1523
Microcontroller: ATmega328P Circuit Operating Voltage: 5V Clock frequency: 16MHz. 6 PWM port: D3, D5, D6, D9, D10, D11. Use For Atmel Atmega328P-AU microcontroller. Support serial download. Support 9V battery. A pair of TTL level serial port transceiver : RX / TX.
Reference: RBD-0343
Model number: TEC1-12706 Operating Voltage: 12V Maximum Voltage Umax (V) : 15.4V Maximum Current Imax (A) : 6A Maximum Power: 92 W Maximum Temperature: 138°C Power Cord: 200mm.RoboticsBD
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0348
A Color-Coded Cable, with a standard male header connectors. Plug it straight into an Arduino or a Breadboard. No soldering is required. The Pulse Sensor has 3 holes around the outside edge which make it easy to sew it into almost anything. Visualization software (made in Processing) to instantly see the output of the sensor and for troubleshooting....
Reference: RBD-0350
100% Brand new and high quality STM32 Board Model: STM32F103C8T6. Core: ARM 32 Cortex-M3 CPU. Debug mode: SWD. 72MHz work frequency. 64K flash memory, 20K SRAM. RoboticsBD 2.0-3.6V power, I/O.
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0410
Supply voltage: 6V-15V Chip: X9C103S Dimensions : 28 x 14 x 4 (LxWxH) mm. RoboticsBD 10K span potentiometer. Potentiometer center tap between the 0-10k slide in total 100 (potentiometer wiper typical impedance 40 ohms)
Reference: RBD-0623
Input voltage range: 6-26V Output voltage: 5.2V (consider the charge line loss, the output is 5.2V or so, the load side is about 5V) Output current: 3A (in the absence of a heat sink device, the stable output current is 2A) Two output Port can charge two devices simultaneously. RoboticsBD
Reference: RBD-0668
Crystal 32.768KHz, matching capacitance 6pF DS1302 8-pin SMD homemade chips Seconds, Minutes, Hours, Day of Month, Day of Week, and Year Operating temperature: 0 degree — 70 degree. RoboticsBD
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-0729
Frequency (MHz) 1575 +/- 5 MHz Gain > 28 dBi (with LNA) Impedance (Ω) 50 Ω VSWR < 1.5 Polarization RHCP Power Handling (W) 50 watts Cable Length: 3Meter Connector: SMA-Male
Reference: RBD-0737
Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-1875
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-2160
Fully compatible with the PC. Moulded strain relief and PVC over moulding to ensure a lifetime of error-free data transmissions. Aluminium under mould shield helps meet FCC requirements on KMI/RFI interference. Foil and braid shield complies with fully rated cable specifications reducing EMI/FRI interference.
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-2309
Add Internet to your next project with an adorable, bite-sized WiFi microcontroller, at a price you like! This module contains an ESP8285, which is an ESP8266 processor with 1MB of FLASH memory already built in. You can use it just like an ESP8266, it's the same processor and WiFi The ESP8266 processor from Espressif is an 80 MHz microcontroller with a...
Reference: RBD-2413
Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...
Reference: RBD-2651
D1 Mini board with 4 MB flash memory and ESP8266 chipset. The board can be programmed with Arduino IDE, has the CH340 USB chipset and allows you to create IoT devices quickly and easily.
Reference: RBD-2652
Firstly, In terms of pins, the D1 Mini and NodeMCU V3 development boards are quite similar. They both break out all ESP8266 ESP-12E/F pins. The NodeMCU V3 board has additional 3V3 and GND pins. Hence, it is more suitable for various connections to devices with an additional button for the flash. Furthermore, you can flash either board with NodeMCU...
Reference: RBD-0963
Current and voltage display in turn, easy and comfortable to use. Small and portable, do not need other power supply. Measuring range: DC 3V – 9V / 0 – 3A (up to 5A ) Portable Device Interface: USB2.0, USB3.0 Product Weight: 0.025 kg Two output ports
Reference: RBD-1326
Outer Diameter: 68 mm. Supply Voltage: DC 4-7V. LED driver chip: WS2812B Communication interface: single wire communication. Send data at speeds of 800Kbps. The color of the light was highly consistent Full-color module, Full-color soft lights a lamp strip
Reference: RBD-1524
Input Voltage(VDC): 4 ~ 40. Output Voltage(VDC): 1.3 ~ 37. Output Current: 2A Rated, ( 3A maximum with heat sink). Switching Frequency: 150 kHz. Input reverse polarity protection. Built-in output short protection function.
Reference: RBD-1545
Input voltage 9~40V Output: 5V Maximum output current 2A Efficiency: 76-90% Material: electronic component
Reference: RBD-1676
L Shape 3.5Mm Right Angle Female To Male Plug Adapter Connector
Reference: RBD-1742
Holds 10 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 78X 60 X 28 Weight: 27.4 gm Material: Plastic Internal Connection: Series
Reference: RBD-1815
I/O Isolation for MCUs (Micro Controller Units) Noise Suppression in Switching Circuits Driving Port Signal Voltage: 3.6-24V Output Port Voltage Port: 3.6-30V Output Can Be Switched From Pull-Up or Pull-Down With Jumpers.