Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-1746
Neodymium Magnet Shape: Disc Dimension: 10mm x 1mm
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-2695
Custom 3D-printed enclosure designed specifically for the US-015 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. Features two screw holes for convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-1107
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness Easy to Use with PCB Mounting as well as on Breadboard
Reference: RBD-2696
Custom 3D-printed enclosure designed specifically for the HC-SR04 ultrasonic sensor module. Protects the sensor from dust, moisture, and impacts for enhanced durability and performance. For convenient and secure mounting in various projects. Note: Filament Color may change as our stock rotates.
Reference: RBD-1109
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 20 Low Current Consumption High Brightness
Reference: RBD-2027
5.08mm pitch. Pin header: Tin plated brass. Contacts: Nickel plated brass. Strong, compact, lightweight. Heat resistant.
Reference: RBD-1108
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness
Reference: RBD-2021
Current Rating: 3A Voltage Rating: 250V Connector Type: Header JST-XH 4 Pin Connector
Reference: RBD-1305
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common anode No. of Pins: 10 Low Current Consumption High Brightness
Reference: RBD-1306
Easy to Install on Breadboard. Bright LED lights. Compact Design. LED Size: 3mm. Configuration: Common Anode.
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-1659
Dimension: 5×7 CM Quantity : 1 PCS Base Material FR4 Copper Thickness 1-4 OZ Board Thickness 1.6 PCB Weight; 10 gm PCB color: Green
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-2049
Rotation Angle: 300° ±10° Gyroscopic Moment: 10-200gf.cm Rotational Stopper Strength: 3Kgf.cm Push-Pull Strength: 8kGF Max Shaft Wobble: 0.6xL/20MM p-p Max Total Resistance Tolerance: ±20% Residual Resistance: R less than or equal to 10K Ohms 10 Ohms Withstand Voltage: 1 minute at 300V AC Rotation Life: 10000 times Can be used as a 10K contrast...
Reference: RBD-1115
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1116
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1117
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1118
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1119
Connects PCBs: Ideal for connecting PCBs (Printed Circuit Boards) with through-hole mounting. Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 male pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.
Reference: RBD-1120
Connects PCBs: Ideal for creating secure connections between PCBs (Printed Circuit Boards). Standard Pitch: 2.54mm pitch ensures compatibility with various components. Easy Integration: Single row of 40 female pins simplifies assembly. Durable Construction: Made with high-quality phosphor bronze for reliable connections.