Reference: RBD-0276

INA125P IC

1 review

LOW QUIESCENT CURRENT: 460µA PRECISION VOLTAGE REFERENCE: 1.24V, 2.5V, 5V or 10V SLEEP MODE LOW OFFSET VOLTAGE: 250µV max LOW OFFSET DRIFT: 2µV/°C max

Reference: RBD-0390

12V 37GB550 Gear Motor High Torque 60 RPM

3 reviews

Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).

Reference: RBD-0042

Mini RC Quadcopter 2013 Robotics Bangladesh

Latest 6-axis flight control system with adjustable gyro sensitivity Permits super stable flight Lightweight airframe with nice durability

Reference: RBD-0218

High Torque Gear Motor 12V, 50 RPM

High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM

Reference: RBD-0344

Weighing Sensor 24 Bit Load Cell Amplifier HX711

13 reviews

Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD

Reference: RBD-0383

ADS1115 16 Bit I2C 4 channel ADC Module

1 review

Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference

Reference: RBD-0385

MCP23017 I2C 16 Input/Output Port Expander

2 reviews

IC Name: MCP23017 Package/Case: DIP-28

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

1 review

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-0560

MAX485 RS-485 Module TTL to RS-485 module for Arduino

5 reviews

On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...

Reference: RBD-0167

RFID Reader ID-20LA (125 kHz) (Retired)

(Retired) Description: RFID (radio-frequency identification) is the wireless non-contact use of radio-frequency electromagnetic fields, for the purposes of identifying and tracking tags attached to objects. This is the ID-20LA, a very simple to use RFID reader module from ID Innovations. With a built in antenna, the only holdup is the 2mm pin spacing....

Reference: RBD-0170

Brand: SparkFun Electronics

RFID Starter Kit - Retail (Retired)

(Retired)

Reference: RBD-0695

MAX31865 SPI PT100/PT1000 RTD-to-Digital Converter Board

Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:

Reference: RBD-0186

WiDo - Arduino WIFI IoT Node (Retired)

1 review

(Retired) WiDo - Arduino WIFI IoT(Internet Of Things) Node (Arduino Compatible) Wido is an Arduino compatible WIFI IoT Node development board, which integrates with WG1300 WIFI solution. The microcontroller of Wido is ATMEL ATmega32U4.

Reference: RBD-1344

Current to Voltage Transmitter Module

Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V

Reference: RBD-0211

Leap Motion Controller (Retired)

(Retired) The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible  speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,

Reference: RBD-1068

N20 12V 100 RPM Micro Metal DC Gear Motor

8 reviews

This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.

Reference: RBD-1248

Miniature Vibrating Motor

3 reviews

Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V

Reference: RBD-1834

PT100 to 0-5V Converter PCB-mounted PT100 to 0-10V Conversion Module RTD PT100 to Voltage Signal Conditioner

PT100 to 0-5V Converter Voltage Signal Conditioner PCB-mounted

Reference: RBD-1346

Mini Servo SG92R

9 reviews

Model: SG92R Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 2.5kg-cm

Reference: RBD-0029

Raspberry Pi Model B (Made in UK) (Retired)

2 reviews

The first-generation Raspberry Pi Model B was released in February 2012 SOC BCM2835 Memory 256 MB Standard Form Factor  Ethernet available. Wireless (Wifi/Bluetooth) not available. GPIO 26 pin

Reference: RBD-0013

AVR ISP MKII

Arduino Programming Supports fuses and lock bit programming Upgradeable for future device support Supports target voltages from 1.8V to 5.5V Adjustable ISP programming speed (50Hz to 8MHz SCK frequency) USB 2.0 compliant (full speed, 12Mbps) Powered from USB, does not require external power supply Target interface protection Short-circuit protection...

Reference: RBD-1870

RS485 To TTL Module Stable UART Serial Port To RS485 Converter Function Board

Compatible with 3.3V and 5.0V power supply. Compatible with 3.3V and 5.0V signal.  Semi-hole pads, onboard module, thin PCB, having a thickness of 0.8mm.  Has RXD, TXD signal indicator light, monitor send and receive status.

Reference: RBD-0025

Arduino Ethernet Shield Basic

With this Ethernet Shield, your Arduino board can be connected to internet Uses ENC28J60 SPI Ethernet controller and compatible HR911102A RJ45 socket Web client application to use Arduino as a distributed network sensor Stackable by accepting prototype shield or any other boards with Arduino compatible interface

Reference: RBD-0336

12V 45KG Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM

12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 54 Torque: 40KG.CM

Reference: RBD-0363

12V 35KG Torque Turbo Worm Gear DC Motor with Metal Gearbox 100 RPM(Retired)

1 review

12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 100 Torque: 35KG.CM

Reference: RBD-0021

High Torque Gear Motor

2 reviews

Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions

Reference: RBD-0039

HC-SRF05 Ultrasonic Sensor

Model: HY-SRF05 Voltage : DC5V  Static current : less than 2mA  Detection distance: 2cm-450cm  High precision: up to 0.3c

Reference: RBD-0043

FEZ Hydra Basic Kit

Description: FEZ Hydra is a 100% open-source (hardware and software) .NET Gadgeteer compatible mainboard running .NET Micro Framework. It incorporates a 240Mhz AT91SAMRL ARM9 processor. With 16MB of SDRAM an 4MB of FLASH, FEZ Hydra is capable or running the most complex applications. The Basic Kit includes the essential modules needed to get started with...

Reference: RBD-1920

Programmable Relay Timer Module USB Smart Home Controller

Compared with electromagnetic relay products, the service life is longer. This product can realize fast switching of the circuit, and the number of switching is unlimited. Most equipment can use this product as it is very convenient; The interface is clear and simple, powerful, easy to understand, and almost meets all your needs. The module is featured...

Reference: RBD-0044

Brand: SparkFun Electronics

FEZ Panda II

Description: The 72Mhz FEZ Panda II runs .NET Micro Framework, allowing users to program and debug FEZ Panda using Microsoft's free Visual C# Express. Applications are loaded over USB cable (or serial) with full featured debugging capabilities, such as stepping in code or inspecting variables.

Reference: RBD-0045

Netduino 2

Description: Netduino 2 is still the same Arduino shield compatible board you know and love, except faster with more code space. Powered by an STmicro Cortex-M3 microcontroller running at 120MHz, the Netduino 2 packs 192KB of code space and 60KB of RAM. With built-in hardware peripherals like UART, PWM, I2C, 12-bit ADC and DAC, the Netduino 2 is ready to...

Reference: RBD-0047

Brand: SparkFun Electronics

Maple

2 reviews

In the past, ARM processors were notoriously unfriendly in non-professional environments due to proprietary tool chains and unfamiliar instruction sets. Because of this, they were conspicuously absent from classrooms and hobbyists’ workbenches. LeafLabs aims to change this by providing an ARM tool-chain built from open source components and a programming...