Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0335
Features: Simonk Programe, Perfect drive Low voltage, over heat protection, with power on self detection function MCU and BEC with independant regulator, high anti-interference ability Throttle stroke adjustable, compatiable with different receivers, good low speed performance
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0378
Model: Eachine 1000TVL 1/3 CCD Lux: 0.08Lux/ F1.2 Sensor: 1/3 “CCD Format: NTSC/PAL(Free switch) Resolution: a.Ultra High Definition 1000TVL b.PAL: 976H X 582V c.NTSC: 976H X 494V Lens: 2.8mm IR coated. RoboticsBD FOV: 110 °
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-0379
TS832 RC832 5.8G 32CH 250mW FPV Transmitter Receiver 7.4-16V
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-0380
Eachine VR D2 40CH 5 Inches 800 x 480 Raceband 5.8G Diversity FPV Goggles with DVR Lens Adjustable
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-0381
Operating Voltage:6~28 VDC Max Input Voltage:28 V DC Max Current Sensing: 90 A Connecting Type:XT-60 RoboticsBD
Reference: RBD-1138
Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v
Reference: RBD-1327
Package includes: 1 pcs x Acrylic Box ( without W1209 module ) DIY cover for W1209 Control Module Acrylic material looks transparent(may need to tear down the film). Easy for electronic enthusiasts to assemble.
Reference: RBD-0437
Power supply range: 3.7-5V 100mA Resolution: 1280 x 960 Resolution: 600TVL Illumination: 0.5LUX Format: PAL / NTSC Audio Lens: Wide-angle 1.8mm (170º) Image sensor:1/4 CMOS image sensor Sensitive area: 3.5964mm x 2.7084mm Size of the lens: M10
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-1410
Compatible with Nvidia Jetson Nano Easy to assemble Slots to access all ports Cut-out for a fan at the top
Reference: RBD-0556
Framework: 12N14P KV: 1400KV LiPO Batteries: 2-3S Max. thrust: 930-940gm Shaft: 3mm Propeller: 9-10″
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-0571
Item Name: T plug Quantity: 1 male & 1 female Body Material: Brass and gold plated Internal Material: Nylon/PA Internal Resistance: 0.4mΩ
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: RBD-1692
Color: Black lightweight Convenient to carry this battery box holder with wires Weight: About 9g Wire Length: Approx 14cm
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-0660
Material: glass fiber Can connect 1-4 ESC. RoboticsBD This has an XT60 plug to connect a battery.
Reference: RBD-1742
Holds 10 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 78X 60 X 28 Weight: 27.4 gm Material: Plastic Internal Connection: Series
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-0704
3-axis high-performance MEMs gyros and 3-axis high-performance MEMs accelerometer. Tiny 36 x 36 mm 4 layer PCB for superior electrical noise reduction and flight performance. Software support for Windows, Mac, and Linux. Direct high-speed USB support with no drivers required, a true plug and play device. Spektrum satellite receiver support. Futaba S-BUS...
Reference: RBD-1743
Holds 6 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 58X 48 X 28 Weight: 15.6 gm Material: Plastic Internal Connection: Series
Reference: RBD-0718
Model Type: Digital Radio Transceiver. Sensitivity: 1024. Bandwidth: 500 kHz. Default Operating Mode: Mode 2 (Left-Hand Throttle). No. of Channels: 6. Operating Voltage: 12V DC (1.5AA x 8 Battery) (not included).
Reference: RBD-1255
Integrated 0.96″ OLED Micro USB connection Compatible with Arduino Compatible with NodeMCU(Lua for ESP8266) Input Power 5V Compatible for Arduino Compatible with NodeMCU(Lua for ESP8266)
Reference: RBD-1828
Sleek aluminum alloy enclosure Plastic base for excellent Wi-Fi signal strength Easy installation with magnetic removable top Easily accessible GPIO with color-coded pinouts M.2 SATA SSD NOT INCLUDED