Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0145
Dual output mode, analog output more accurate A fixed bolt hole for easy installation With power indicator (red) and digital switching output indicator (green) Having LM393 comparator chip, stable. Operating Voltage: 3.3V~5V
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum. RoboticsBD
Reference: RBD-1656
L-Shaped DC Gearmotor Nominal Voltage: 6V No Load RPM: 180 Stall Current: 2.8A Stall Torque: 11.11 oz-in Shaft Diameter: 5.5 mm (Double-Flat) Comes with Back Shaft
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-2185
Operating Voltage: 3 VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 8 mm front and rear(approx.) Weight; 19g (approx.)
Reference: RBD-2190
Operating Voltage: 1.5 to 3VDC Shaft Diameter: 2 mm (approx.) Shaft Length: 5mm (approx.) Weight; 22.5g (approx.)
Reference: RBD-2519
Small 1.5 – 3V DC motor with fan for science projects or general experimenting 3V DC motor with cable Soft 3-leaf fan bladeThe Jumper may become detached during shipping and require soldering with a soldering iron.
Reference: RBD-0925
Hold 4 standard 18650 batteries. Wire Length: 15 cm. Output: 14.8 V. Dimension (Appro.) : 80 x 76 x 18 mm. Weight: 28 gm. High-quality plastic material
Reference: RBD-1041
PCB Size: 60 x 20 x 13.5 (LxWxH)mm. Color: red, yellow, green LED Size: 10mm x 7. Brightness: Normal brightness. Voltage: 5V. Interface: common cathode red yellow green control.
Reference: RBD-2859
Small metal vibrating motor powered by 3 V. Idle current 90 mA. Dimensions: 9 x 5.2 x 5.2 mm.
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-1198
Industrial Systems Consumer Products Thermometers Thermally Sensitive Systems
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-1208
Working Voltage: 5V DC Operating Temperature: -30ºc ~ 85ºc Output high level when received the laser signal Output low level when not receive laser signal. Application: Electronic Circuits
Reference: RBD-1768
Locking On/Off Switch Green LED Power Indicator Voltage Swapping Switch on both rail Channel Its concave design will not waste your proto zone. Easy to install on a breadboard with Compact portable size
Reference: RBD-1347
TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.
Reference: RBD-1944
Cell Quantity: 5 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-2564
This MOSFET module with optoisolation uses the LR7843 N-Channel logic compatible MOSFET with ultra low Rds(on) for moderate to higher current low-side switching applications of up to 15A continuous. N-Channel logic compatible MOSFET with optoisolation and ultra low 3.3mΩ Rds(on)
Reference: RBD-2755
When you need to switch a lot of power, P channel MOSFETs are best for the job. These P-FETs can switch over 60V and 25A (with proper heat-sinking) and are TO-220 package so they fit nicely into any breadboard or perfboard. Heat sinking is easy with TO-220s, but because of the very low Rds(on) of down to 70 mOhms (depending on the Vgs - check the...
Reference: RBD-2080
Clean, good waveform driving ability, more than 15mA. Working voltage 3.3V-5 Output format: digital switching output (0 and 1) A fixed bolt holes for easy installation
Reference: RBD-2091
Digital signal output 18B20 Temperature Sensor Chip (MY18E20 or DS18b20) Resolution adjustment ranges from 9-12 bytes. Send data via a pin Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.Compatible with DS18B20
Reference: RBD-2144
Automatic induction: to enter the sensing range Ultra-small size. Repeatable trigger Wide operating voltage range Micropower: quiescent current <50 Output high signal: easy docking and all kinds of circuits.
Reference: RBD-2446
This is the updated 2021 version of the HC-SR04 Ultrasonic Sensor, offering enhanced features and improved flexibility. Notably, the input voltage now ranges from 2.8V to 5.5V, providing compatibility with a wider range of microcontrollers, including both 3.3V and 5V systems. Mode 1: GPIO (General Purpose Input/Output) Mode 2: I2C (New Feature) Mode 3:...
Reference: RBD-2790
The US1881 is an integrated Hall-Effect latched sensor. That's nice but what does it do? Holding a magnet near the sensor will cause the output pin to toggle. This makes for a robust presence sensor. A reed sensor also works nicely, but can be limited by the glass encapsulation and size. A Hall-Effect sensor is much smaller, but can handle less current...
Reference: RBD-2799
This is the HC-SR04-33 ultrasonic distance sensor. This economical sensor provides 2cm to 400cm of non-contact measurement functionality with a ranging accuracy that can reach up to 3mm. Each HC-SR04-33 module includes an ultrasonic transmitter, a receiver and a control circuit. There are only four pins that you need to worry about on the HC-SR04: VCC...