Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-0549
Breadboard power supply module, compatible with 5V, 3.3V. RoboticsBD Apply to MB102 breadboard Input voltage: 6.5-12 V (DC) or USB power supply Output voltage: 3.3V/5V can switch over Maximum output current: <700 ma Fluctuation two road independent control can switch over to 0 V, 3.3 V, 5 V On-board two groups of 3.3V, 5V DC output plug pin, convenient...
Reference: RBD-0376
Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes
Reference: RBD-0732
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-0571
Item Name: T plug Quantity: 1 male & 1 female Body Material: Brass and gold plated Internal Material: Nylon/PA Internal Resistance: 0.4mΩ
Reference: RBD-0388
Input voltage : 4.5V ~ 5.5V. Input Interface: Micro USB port. Charging method: linear charge. A full charge voltage: 4.2V. RoboticsBD Power: 4.2 w. Charging accuracy: 1.5%. Operating Temperature: -10 to +85ºC Charging indicator: Blue LED charging, Red LED full Check out New Product TP4056 Lithium Battery Charger Module With Protection Dual Functions
Reference: RBD-0435
Supply Voltage : 8-35 VDC. Current : 1.0A (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.
Reference: RBD-0395
Input voltage range: 4V-38V DC Output voltage range: 1.25V-36V DC adjustable. Output current: 0-5A. Output power: 75W. High efficiency up to 96% The built-in thermal shutdown function Built-in current limit function In-Built output short protection function. RoboticsBD
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0652
Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. RoboticsBD
Reference: RBD-0406
Input voltage: 4.5-35V, Output voltage: (3-35V) continuously adjustable (recommended load debugging). Minimum pressure: 1.5V Output current: rated current 2A, 3A maximum Output Power: 15W maximum. RoboticsBD
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-0919
Dimension: 25 x 19 x 10 (LxWxH)mm. Input interface: micro USB. Current Protection: Yes Charging mode: Linear charging. Current: 1A adjustable. Charge precision: 1.5%. Input voltage: 4.5V-5.5V. Full charge voltage: 4.2V.
Reference: RBD-0988
Hold 3 standard 18650 batteries. Wire Length: 15 cm. Output: 11.1 V. Dimension (Appro.) : 76 x 60 x 18 mm. Weight: 18 gm. High-quality plastic material
Reference: RBD-1606
Supply Voltage Range: 4.75V to 7V Driver Case Style: DIP No. of Pins: 20 Operating Temperature Range: -40°C to +150°C
Reference: RBD-0989
Hold A standard 18650 batteries Wire : 15cm Output: 3.7v Dimension (Appro.): 76x20x20xmm Weight: 8gm High-quality plastic material
Reference: RBD-1724
Operating voltage: DC4.5V-35V Output current: 0-5A Output power: 90W (max) PWM duty cycle: 1% -100%. PWM frequency:20khz Wide voltage DC motor speed controller.
Reference: RBD-0748
Length: 8″. Pitch: 4.5″. Weight: 20 gm. Shaft Diameter: 9.5mm. Total Length: 8 inch / 200 mm. It comes with a set of plastic reducers (3,3.17,4,5,6,8 mm).
Reference: RBD-1810
Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver
Reference: RBD-1912
New L293D motor shield, the input voltage DC4.5-25V 600mA output current capability per channel 1.2A peak output current(non-repetitive) per channel Enable facility Overtemperature protection Logical “0” input voltage up to 1.5V(High noise immunity)
Reference: RBD-0825
Improved Locking Gold Plated Connectors tip Color: Red High-Quality built and Material Good resistance to Temperature & High Amp. Current
Reference: RBD-0826
PolyMax 3.5mm Gold Connectors 3.5mm sprung gold connectors handle the large current, 50A+ systems. perfect for 3500mAh or larger capacity batteries
Reference: RBD-1646
Input Voltage: 220VAC Output Voltage: 5 VDC. Output Power: 3.5W. Output overload and short circuit protection.
Reference: RBD-1055
Length: 5″. Pitch: 4.5″. Weight: 27 gm. Shaft Diameter: 5mm. Total length: 5 inch / 125 mm. Material: Poly-Carbonate.
Reference: RBD-2511
Switching a lot of power? N-channel power MOSFET - 30V / 60A IRLB8721 MOSFETs are just what you need.These TO-220 package power MOSFETs can switch 30V/60A, which is plenty for most makers! They fit straight into a breadboard or even your own PCB with 2.54mm spaced pads.
Reference: RBD-0940
Good Quality Type: Male-Female Plated Connectors Length: 10 cm Color: Red and Black
Reference: RBD-1705
3A DC-DC Buck Step-down Converter Constant Voltage 5V Fixed Output Module
Reference: RBD-2834
Enhance your 3D printer's performance with the DRV8825/A4988 Stable 42 Stepper Motor Driver Expansion Board. This expansion board offers advanced features and superior performance to meet your diverse needs in 3D printing and DIY projects.Note: Please ensure correct installation direction of the drive module to prevent module damage.
Reference: RBD-1754
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1771
It’s efficient up to 93% It can source a good amount of current The maximum output current: 2A Input voltage: 2V-24V DC The maximum output voltage: 5V-28V DC