Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: RBD-0284
Gain: 2.0dBi-2.5dBi Antenna connector: RP-SMA Male Connector Standing wave ratio(SWR): <1.5 Weight: TxA10.3g, RxA 11.5g TxA is a circular-polarized Omni antenna with three lobes RxA is a circular-polarized Omni antenna with four lobes
Reference: RBD-0566
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Reference: RBD-2386
Brand: Raspberry Pi Official
The Raspberry Pi Pico W builds upon the great cost-for-performance metrics of the Pico and add WiFi to the board. The Pico W features the same attributes as the Raspberry Pi Pico and also incorporates an Infineon CYW43439 wireless chip. CYW43439 supports IEEE 802.11 b/g/n wireless LAN, and Bluetooth® 5.2. (6/30/2022: Only Wireless LAN is supported on the...
Reference: RBD-1599
Brand: Raspberry Pi Official
RP2040 microcontroller chip designed by Raspberry Pi Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz 264KB of SRAM, and 2MB of onboard Flash memory 26 × multi-function GPIO pins 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels Temperature sensor
Reference: RBD-2012
Brand: Raspberry Pi Official
RP2040 microcontroller chip designed by Raspberry Pi Dual-core Arm Cortex M0+ processor, the flexible clock running up to 133 MHz 264KB of SRAM, and 2MB of onboard Flash memory 26 × multi-function GPIO pins 2 × SPI, 2 × I2C, 2 × UART, 3 × 12-bit ADC, 16 × controllable PWM channels Onboard temperature sensor
Reference: RBD-1734
Center female pin header for direct attaching the Raspberry Pi Pico. Extra USB connector for external power supply. Immersion Gold Process Black Base Panel, White Pinout Labels, Golden Rounded Outline, Stunning Aesthetic *Please make sure there are no pin conflicts between the modules you want to use together before connecting. Raspberry Pi Pico and...
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-1971
Brand: DFRobot
Gravity Expansion Board Designed for Raspberry Pi Pico Compatible with a variety of Gravity sensors and modules. Gravity Expansion Board for Pico All pins brought out, no soldering required Additional Communication Ports: Digital IO, Analog IO, I2C, SPI, UART, GDI Note: The product not include Raspberry Pi Pico. Buy Raspberry Pi Pico here. Buy Raspberry...
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-0738
Resolution: 5 MP Interface Type: CSI(Camera Serial Interface) Dimensions: 25x23x8 (LxWxH) mm Supported Video Formats: 1080p @ 30fps, 720p @ 60fps and 640x480p 60/90 video Fully Compatible with Raspberry Pi 3 and 4 Model B Plug-n-Play camera for Raspberry Pi 3 and 4 Model B.
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-1143
Type: Raspberry Pi 4 Model B Aluminum Alloy Metal Case Material: Black/Silver Aluminum Alloy Metal Compatible For Raspberry PI4 Model B Easy to install, Ultra-thin design. All ports and slots of the case can match with Raspberry Pi 4 Model B perfectly
Reference: RBD-1134
Easy to Assemble Comes With all Components Operating Voltage: 5VDC Operating Current: 200mA Compatible With Arduino and Raspberry Pi
Reference: RBD-1337
Transmission Distance(m) :400 Relay Channel:2 Trigger Voltage (VDC): 5 Switching Voltage (VAC):250@10A Switching Voltage (VDC):30@10A Baud Rate:9600 Note: Relay might be different from the picture as per stock
Reference: RBD-1596
Brand: Raspberry Pi Official
Good Quality material 96-230Vac operating input range 50,000 hours MTBF Input Current: 0.5A maximum Input Power consumption (no load): 0.075W maximum USB-C connection goes straight into your Raspberry Pi
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-0841
Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900 Connect onto any global GSM network with any 2G SIM Make and receive voice calls using an external 8Ω speaker & electret microphone Facility to connect 4-pole TRRS mic and headset
Reference: RBD-1529
Model:SX1278ZTR4 SX1278 433mhz module spread spectrum low power serial port module LoRa wireless module Range: 3-5 KM (line of sight) Sensitivity: down to -148dBm Programmable bit rates: up to 300kbps RSSI dynamic range: 127dB Wireless frequency: 433MHz Working voltage: 1.8-3.7v Working temperature: -40-+80 ℃
Reference: RBD-1552
Working Frequency: 868 MHz Distance: 8000m RF IC: SX1276
Reference: RBD-1603
USB-TTL converter. Logic Level: 5V. Operating Supply Voltage: 5V. Digital I/O Pins: 14. Analog I/O Pins: 6.
Reference: RBD-1647
Communication distance: 15KM Sensitivity: down to -148dBm Programmable bit rates: up to 300kbps RSSI dynamic range: 127dB Wireless frequency: 433MHz Working voltage: 1.8-3.7v Working temperature: -40-+80 ℃
Reference: RBD-0939
RGB Backlight Keys Onboard trackpad with all mouse function Left+Right click Gaming keys Operate on inbuilt Rechargeable battery Navigation, Volume Rockers and Home key Portable Pocket Size Plug and Play operation, No drivers needed to install Compatible with all Devices and operating Systems
Reference: RBD-1058
Remote control distance: more than 8 meters Power Supply: CR2032 Battery Compatible with: Windows, Raspberry Pi
Reference: RBD-1870
Compatible with 3.3V and 5.0V power supply. Compatible with 3.3V and 5.0V signal. Semi-hole pads, onboard module, thin PCB, having a thickness of 0.8mm. Has RXD, TXD signal indicator light, monitor send and receive status.
Reference: RBD-1928
Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.
Reference: RBD-2135
433 Mhz Remote Control and Wireless Receiver Module Learning Code 1527 Decoding 4 Channel Output with Learning Button DIY kit for Arduino/ARM/MCU Suitable for wireless power switches, remote control sockets, LED lights, electric doors, and more.
Reference: RBD-2136
Very Few External Components Excellent Receiver Sensitivity and Robustness to Interference. Programmable Output Power Up to 4.5 dBm. High-Quality Construction
Reference: RBD-2212
Directly plug antenna interface. I2C bus communication. Multi-capacitor combined filter. Blue LED power indicator. High sensitivity(low noise RF input amplifier). High power auto gains control AGC circuit.
Reference: RBD-2295
The CC2530 ZigBee series wireless module launched by BEE Iot Technology is a ZigBee RADIO frequency module developed based on TI's CC2530F256 chip. The module can complete ZigBee learning, project application, and industrial production, and can be widely used in the field of short-distance wireless communication networking. It can build powerful network...
Reference: RBD-2327
Brand: DFRobot
In life, remote controllers can be seen everywhere, and most of them are inseparable from the battery. However, we often encounter problems when using the battery, for instance, it is troublesome to replace the battery, batteries are easy to corrode in a humid environment, or the waste batteries may cause serious environmental pollution. Do you know that...