Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-0326
Very handy and simple in assembling/disassembling. RoboticsBD Strong components so as to withstand extreme terrain conditions. Transparent Car Chassis. Attractive design. RoboticsBD
Reference: RBD-0102
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they're usually unreliable or difficult to implement. Well not anymore! We've found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
Reference: RBD-0142
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
Reference: RBD-0100
Description: This robotic claw is a step up from the classic. The MKII takes everything you loved about the standard robot claw from DAGU and makes some significant improvements!
Reference: RBD-0268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: RBD-0166
Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...
Reference: RBD-0208
"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."
Reference: RBD-0233
Brand: SparkFun Electronics
Description: This is the LSM9DS0, a versatile motion-sensing system-in-a-chip that houses a 3-axis accelerometer, 3-axis gyroscope, and 3-axis magnetometer. That’s right, 9 degrees of freedom (9dof) from a single IC!
Reference: RBD-0235
Brand: SparkFun Electronics
Description: This is a framed graphical LCD 64x128 with LED backlight. This unit is a very clear STN type LCD with a simple command interface. This new module includes the negative voltage circuitry on board!
Reference: RBD-0237
Description: This Telemetry radio set allows you to link to a flight controller such as the APM or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)
Reference: RBD-0231
Brand: SparkFun Electronics
Sitara AM3358BZCZ100 ARM Cortex-A8 32-Bit RISC microprocessor, up to 1GHz Onboard HDMI to connect directly to TVs and monitors More and faster memory now with 512MB DDR3L 400MHz SDRAM, 4GB eMMC Memory Onboard storage frees up the microSD card slot for greater expansion Support for existing Cape plug-in boards TPS65217C PMIC regulator and one additional...
Reference: RBD-0258
Brand: SparkFun Electronics
SparkFun Micro OLED Breakout
Reference: RBD-0267
Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0274
Brand: Waveshare
5 inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi Installation Instruction: http://www.waveshare.com/wiki/5inch_HDMI_LCD Raspbian Image for 5 inch HDMI Diplay with Touch : Raspbian 5 inch HDMI with Touch Download Link
Reference: RBD-0334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: RBD-0338
Brand: Waveshare
Sharp GP2Y1010AU0F onboard, Detecting fine particle larger than 0.8μm Low power consumption Analog voltage output The output level is linear with dust density Check out New Product Optical Dust Sensor- GP2Y1010AU0F
Reference: RBD-0369
Brand: SparkFun Electronics
Supports binding and multicasting for home automation Mesh-network topology 2.4 GHz for worldwide deployment Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board Firmware upgrades via UART, SPI or over the air TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC DATA RATE: 250kbps Max RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile...
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0562
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-0692
Accuracy: +/- 0.2F.S Temperature coefficient: Less than 150ppm/K F.S. Working temperature: 0-100℃ Working humidity: Less than 98% RH
Reference: RBD-0419
Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...
Reference: RBD-0375
AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)
Reference: RBD-1163
The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.
Reference: RBD-1187
Operating Voltage: 5V Easy to install Comes with Stepwise User manual
Reference: RBD-1264
Car body Material: Aluminum Alloy Car Wheel: Plastic Car strap: Plastic Color: Blue Input Voltage: 12V Weight: 1.2KG Motor & Tanks Chassis is included. No Electronics Parts
Reference: RBD-1311
mDrawBot is a 4-in-1 drawing robot kit it can be assembled into 4 different drawing robots: mScara. mCar. mSpider. mEggBot.
Reference: RBD-1333
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)