Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0274
Brand: Waveshare
5 inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi Installation Instruction: http://www.waveshare.com/wiki/5inch_HDMI_LCD Raspbian Image for 5 inch HDMI Diplay with Touch : Raspbian 5 inch HDMI with Touch Download Link
Reference: RBD-0276
The INA125 is a low-power, high-accuracy instrumentation amplifier with a precision voltage reference. It provides complete bridge excitation and precision differential-input amplification on a single integrated circuit. A single external resistor sets any gain from 4 to 10,000. The INA125 is laser-trimmed for low offset voltage (250µV), low offset drift...
Reference: RBD-0218
High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-0339
Brand: Waveshare
3.5inch Resistive Touch Display (B) For Raspberry Pi 480×320 IPS Screen SPI Check out New Product 3.5inch HDMI Display-B
Reference: RBD-0385
IC Name: MCP23017 Package/Case: DIP-28
Reference: RBD-0235
Brand: SparkFun Electronics
Description: This is a framed graphical LCD 64x128 with LED backlight. This unit is a very clear STN type LCD with a simple command interface. This new module includes the negative voltage circuitry on board!
Reference: RBD-0375
AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)
Reference: RBD-0234
Brand: SparkFun Electronics
Description: This is a 7" LVDS LCD Cape for the pcDuino V3 with a 1024x600 screen resolution and capacitive touch from LinkSprite. This massive screen is a great addition for the pcDuino V3 that compliments its extreme versatility as a mini PC development platform.
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0258
Brand: SparkFun Electronics
SparkFun Micro OLED Breakout
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-1129
Brand: RoboticsBD
Complete Assembled Plug and Play Open Source Design Compatible With Arduino IDE DIY Kit
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-0371
The result of a unique combination of mechanical engineering and software, NAO is a character made up of a multitude of sensors, motors and software piloted by a made- to -measure operating system: NAOqi OS. The pack includes: One NAO V5 (red or blue) 1 Charger and 1 battery 2 years of warranty 1 Choregraphe License Full SDK and API
Reference: RBD-1344
Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V
Reference: RBD-0372
• Comes with the CM-530 controller and AX-12A servos • Convenient, safe and expandable• All-round robot kit for education/robot competitions/entertainment• Can build various types of robot such as spider, dinosaur, and humanoid
Reference: RBD-0374
• Available in kit form or ready to walk • 20 degree-of-freedom humanoid robot comes assembled and ready to use • Controlled by a real-time IR remote, built-in actions or user-programmed actions• Includes graphical software interface
Reference: RBD-1064
Size: 1.3 inch Resolution: 128 x 64 Controlling Chip: SSH1106 Driving Voltage: 3.3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: Blue If you want to purchase White color 1.3 inch OLED display module click here
Reference: RBD-1109
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 20 Low Current Consumption High Brightness
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1305
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common anode No. of Pins: 10 Low Current Consumption High Brightness
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V
Reference: RBD-1306
Easy to Install on Breadboard. Bright LED lights. Compact Design. LED Size: 3mm. Configuration: Common Anode.
Reference: RBD-1328
Size: 0.96 inch Resolution: 128 x 64 Controlling Chip: SSH1106 Display Area: 21.74 x 10.86mm Driving Voltage: 3.3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-1834
PT100 to 0-5V Converter Voltage Signal Conditioner PCB-mounted
Reference: RBD-1634
Size: 0.91 inch Resolution: 128 x 32 Controlling Chip: SSD1306 Display Area: 22.384 x 5.584mm Driving Voltage: 3-5V Operating Temperature: -40~70 celsius Interface Type: IIC Light Color: White
Reference: RBD-1870
Compatible with 3.3V and 5.0V power supply. Compatible with 3.3V and 5.0V signal. Semi-hole pads, onboard module, thin PCB, having a thickness of 0.8mm. Has RXD, TXD signal indicator light, monitor send and receive status.
Reference: RBD-0336
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 54 Torque: 40KG.CM
Reference: RBD-1920
Compared with electromagnetic relay products, the service life is longer. This product can realize fast switching of the circuit, and the number of switching is unlimited. Most equipment can use this product as it is very convenient; The interface is clear and simple, powerful, easy to understand, and almost meets all your needs. The module is featured...