Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0166
Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...
Reference: RBD-0369
Brand: SparkFun Electronics
Supports binding and multicasting for home automation Mesh-network topology 2.4 GHz for worldwide deployment Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board Firmware upgrades via UART, SPI or over the air TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC DATA RATE: 250kbps Max RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile...
Reference: RBD-0237
Description: This Telemetry radio set allows you to link to a flight controller such as the APM or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0201
QUICK OVERVIEW Transmitter: FS-TH9X Upgrade with FS-RM003 2.4GHz Module Receiver: FS-IA10B Default Mode: Mode-2 Input Power: 12V DC (1.5V x 8 AAA Battery) Bidirectional System Frequencies-Hopping Omni-directional High Gain Antenna Low Power Consumption
Reference: RBD-0321
New PT-100 Temperature Sensor AvailableClick Here PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃
Reference: RBD-0334
The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.
Reference: RBD-0957
Item name: FS-RX2A Radio receiver Channel: 10 RF Range: 2.408-2.475GHZ Number of bands: 135 RX Sensitivity: -92dBm 2.4GHz protocol: AFHDS 2A Signal output: IBUS, PPM Compatible Transmitter: All AFHDS 2A Transmitter, Ex.: FS-I6, FS-I6X, FS-I6S, FS-TM8, FS-TM10, FS-I10.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0841
Supports Quad-band: GSM850, EGSM900, DCS1800 and PCS1900 Connect onto any global GSM network with any 2G SIM Make and receive voice calls using an external 8Ω speaker & electret microphone Facility to connect 4-pole TRRS mic and headset
Reference: RBD-2016
Backward compatible with USB 2.0 USS, MDIX support Jumbo packets up to 9 KB Plug and play installation Full-duplex and half-duplex operation of fast ethernet Suspend mode and remote wake up via links and magic packs
Reference: RBD-2064
TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. Note: If you want to buy the cheaper recycled SIM800L Module Click here.
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-2234
¼ wave rubber duck antenna 860-960MHz communication center frequency of 915MHz RP-SMA connector Gain is 2dBi with an overall length of 110mm
Reference: RBD-0667
Input Supply Voltage (VDC): 3.3 ~ 5. Supply Current (mA): measurement 0.3mA standby 60μA. Temperature measurement range: 0~50 degrees. Temperature measurement error: ±2 degrees. Humidity measurement range: 20%~95%RH. Humidity measurement error: ±5%RH. RoboticsBD
Reference: RBD-2350
Waterproof Wireless Switch 433MHz Self-Powered Remote Control Switch Battery-Free Wall Light Switch
Reference: RBD-0813
Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.
Reference: RBD-0823
LDR module 4 PIN Operating voltage 3.3V-5V Signal output indicator light. LDR module 4 PIN Able to detect ambient brightness and light intensity Adjustable sensitivity (via blue digital potentiometer adjustment)
Reference: RBD-0419
Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-1206
Scanning Range: 18M Radius Detection Range: 12M Radius 4cm Ultra-thin Ideal for all kinds of service robot. 8000 times sample rate, the highest in the current economical LIDAR industry 360-degree laser range scanning Low Noise, Brushless Motor New Non-contact Drive OPTMAG Original Design, prolong the life-span Class 1 Laser Safety Standard High-speed...
Reference: RBD-1352
GRID-EYE® INFRARED ARRAY SENSOR Number of pixel 64 (Vertical 8 × Horizontal 8 Matrix) External interface I2C Frame Rate Typical 1fps or 10 fps Operating Mode Normal and Sleep mode
Reference: RBD-0720
Temperature detection of the two-dimensional area: 8 × 8 (64 pixels). Digital output (capability of temperature value output). Compact SMD package (adaptively to reflow mounting). RoHS compliant. RoboticsBD
Reference: RBD-0722
Brand: Raspberry Pi Official
8-Megapixel native resolution high-quality Sony IMX219 image sensor Cameras are capable of 3280 x 2464 pixel static images Capture video at 1080p30, 720p60 and 640x480p90 resolutions All software is supported within the latest version of Raspbian Operating System No Infrared filter making it perfect for taking Infrared photographs or photographing objects...
Reference: RBD-0568
Brand: Raspberry Pi Official
Fixed focus lens on-board Improved resolution – 8-Megapixel native resolution sensor-capable of 3280 x 2464 pixel static images Supports 1080p30, 720p60 and 640x480p90 video Size 25mm x 23mm x 9mm Weight just over 3g Connects to the Raspberry Pi board via a short ribbon cable (supplied) Camera v2 is supported in the latest version of Raspbian, Raspberry...
Reference: RBD-1654
5 In 1 Portable CO2 Detector Air Quality Detector Intelligent Air Detector Temperature and Humidity Sensor Carbon Dioxide Monitor TVOC Formaldehyde Detection HCHO Detector Color Black
Reference: RBD-0569
Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules
Reference: RBD-1833
NEW TYPE AVAILABLE CLICK HERE Measurement range: 0-199 mg/KG Measurement accuracy: +-2%F.s Resolution: 1mg/KG (mg/L) Response time (T90, s): less than 10 Communication port: RS485 Power supply: 5V-24v DC
Reference: RBD-0142
Description: Fingerprint scanners are awesome. Why use a key when you have one right at the tip of your finger? Unfortunately, they’re usually unreliable or difficult to implement. Well not anymore! We’ve found this great fingerprint module from ADH-Tech that communicates over TTL Serial so you can easily embed it into your next project.
Reference: RBD-0387
All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7 x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.