Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0022
Affordable Price Operating Voltage: 5 V Sonar Sensing Range: 2-400 cm Max. Sensing Range: 450 cm Frequency: 40 kHz RoboticsBD
Reference: RBD-0145
Dual output mode, analog output more accurate A fixed bolt hole for easy installation With power indicator (red) and digital switching output indicator (green) Having LM393 comparator chip, stable. Operating Voltage: 3.3V~5V
Reference: RBD-0152
Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation
Reference: RBD-0315
Working voltage: DC 5 V Static current: 3 mA Working temperature: 0 ~ + 70° Output way: GPIO Induction Angle: Less than 15° Detection range:2 cm to 400 cm Detecting precision: 0.3 cm + 1% Sensor size: Approx. 45 x 20 x 1.6mm Hole diameter: Approx. 1mm. RoboticsBD
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0429
High precision determination accurate to 1 Lu for different lights Operating Voltage: 3-5VDC Built-in 16bit A/D converter I2C interface
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-2582
Displays a single digit using bright green LEDs Common cathode configuration for simple wiring 10 pins for easy connection Clear visibility and compact size Ideal for various electronic projects
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-0041
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-0104
Chip built-in 16bit AD converter, 16-bit data output Driver Chip: MPU6050 Operating Voltage: 3-5V DC Communication: I2C/IIC Protocol Gyro Range: ± 250, 500, 1000, 2000 °/s Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0737
Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0401
Display: 8×2 character Outline: 58.0x32.0x10.0 VA: 37.8x16.0 Controller: SPLC780D Character: 2.96x5.56 Driver: 1/16
Reference: RBD-0222
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound
Reference: RBD-0661
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-0150
Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~+40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser
Reference: RBD-0313
Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-0241
Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typical LM35 (working) tested by...
Reference: RBD-1107
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness Easy to Use with PCB Mounting as well as on Breadboard
Reference: RBD-1109
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 20 Low Current Consumption High Brightness
Reference: RBD-1164
For Standard LCD 16x2 with Male Header. Press here For Standard LCD 16x2 with Female Header. Press here For Standard LCD 16x2 with I2C adapter board soldered. Press here. For Standard LCD 16x2 with White Background. Press here. For Standard LCD 16x2 with Blue Background. Press here.
Reference: RBD-1108
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common cathode No. of Pins: 12 Low Current Consumption High Brightness
Reference: RBD-1305
Bright Red LED chip, which is made from AlGaAs on GaAs substrate Blackface and RED LED segments Type: Common anode No. of Pins: 10 Low Current Consumption High Brightness
Reference: RBD-1306
Easy to Install on Breadboard. Bright LED lights. Compact Design. LED Size: 3.7mm. Configuration: Row Common Anode
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD