Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0156
Operating Voltage: 3V-5V High-resolution conversion of light intensity to frequency. Chip pins all has drawn for standard 100. Put the needle (2.54 mm). Mil-convenient for bitmap board. Programmable color and full-scale output frequency. Communicate directly with a microcontroller. Low-profile surface mount package.
Reference: RBD-0212
Input: 110v or 240v A/C (50/60Hz) Cell Count: 2~3s Battery Type: LiPoly Output Current: 3 x 800mA
Reference: RBD-0227
Model: DC 5V 10mm 5N Rated Operating Voltage (VDC): 5 Operation Mode: Push-Pull (Normally Closed) Holding Force (N): 5 Weight:33 gm
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0430
Operating voltage: 4.5V to 5.0 V Output format: 8 Analog and Digital voltages. Optimal sensing distance: 0.125″ (3 mm). RoboticsBD
Reference: RBD-0494
Input Voltage (V): 100 ~ 280 VAC @50 ~ 60Hz. Input current (mA): 100. Output Power: 12V 2A. Input Plug: 2-Pin USA type. Output Plug: 5.5mm DC plug. RoboticsBD Model: STD-120200
Reference: RBD-0561
Model: 0408 Rated Voltage: 3.7 V. Rated RPM: 70000. Wire Length: 8 cm with socket Motor diameter : 4MM Motor Length: 8MM Shaft Diameter: 0.7MM Shaft Length: 5 MM
Reference: RBD-0916
ROHS approved Mini Solar panel The solar cells are encased and protected by a durable outer poly frame Polycrystalline silicon Max work voltage:5V Max work current: 200ma Dimension: 90mm×90mmx3mm RoboticsBD
Reference: RBD-0110
রাস্পবেরি পাই এর জন্য একটি স্ট্যাবল পাওয়ার সাপ্লাই এর প্রয়োজনীয়তা অনেক। আমরা অনেক পাওয়ার সাপ্লাই টেস্ট করে এর এই পাওয়ার সাপ্লাইটির ক্যাপাসিটি সন্তোষজনক পেয়েছি। যদিও মেনশন করা 5V,3A. আমরা আমাদের টেস্ট এ 5V, 1.5Amp+ কনস্ট্যান্ট কারেন্ট পেয়েছি। যদি আপনার খুব বেশি পেরিফেরাল না দরকার হয় তবে এটি ব্যবহার করতে পারেন। এছাড়া আমাদের কাছে অরজিনাল রাস্পবেরি পাই এর...
Reference: RBD-0159
Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...
Reference: RBD-0259
Smart car chassis tracing car Robot car chassis with code disk, Ideal for DIY. This car is the tachometer encoder. With a 4 AA battery box (batteries not included). It can be used for distance measurement, velocity. Can use with other devices to realize function of tracing, obstacle avoidance, distance testing, speed testing, Wireless remote control....
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-0354
Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD
Reference: RBD-0423
Detecting range: >120 degree Analog and digital outputs On-board potentiometer and indicators 1% resistors to make this module more reliable and precise Operating Voltage: 3.3V – 9V Board Diameter: 40 mm.
Reference: RBD-0425
Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD
Reference: RBD-0432
Iron Body Material High quality ultra-compact electric lock. RoboticsBD Rustproof, durable, safe, convenient to use. Suction which tightly sucks the iron, thus locking the door. Designed with the open frame type and mount board, high power. Easy to install for the electric door lock or other automatic door lock systems with the mounting board Applicable...
Reference: RBD-0439
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....
Reference: RBD-0624
Operating Voltage: DC 2V- 9V Operating frequency: 85MHZ - 115MHZ Output Impedance: 50 ohms
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-0824
Material: glass fiber Can connect 1-4 ESC. This has an T connector plug to connect a battery.
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-2218
Module package (with FLASH memory and peripheral circuits) have DIP16, DIP28, chip packaging has DIP18, SSOP20, and LQFP32 form. Built 13Bit/DA converter, and 12Bit/PWM output. PWM output can directly drive 0.5W/8Ω speakers, push-pull current abundant support DAC / PWM output of two ways. Support for loading WAV audio formats. USB download mode, support...
Reference: RBD-2489
Wiznet Compact W5500 Network Module - 10/100 Base T WIZ850io is a compact size network module that includes a W5500 (TCP/IP hardwired chip and PHY embedded), a transformer and RJ45. It can be used as a component and no effort is required to interface W5500 and Transformer. The WIZ850io is an ideal option for users who want to develop their Internet...
Reference: RBD-2870
Effortless Wire Stripping and Twisting: Saves time and reduces hand strain with fast, automated operation. Universal Compatibility: Works with various wire sizes for maximum versatility in your projects. Durable Construction: High-quality steel construction ensures long-lasting performance. Drill-Powered and Manual Operation: Offers flexibility for both...
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-0228
Color: Black Material: Glass-fiber Suit for different open-source flight controllers, like APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4 Package Weight: 24 gm.
Reference: RBD-0289
Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-0441
Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust RoboticsBD
Reference: RBD-0562
Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm