Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0442
Holding force: 0.25 kg Energized forms: intermittent Unlocking time: 1s Dimensions: 27 x 29 x 18 mm (LxWxH) High quality ultra-compact electric lock. RoboticsBD
Reference: RBD-0218
High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM
Reference: RBD-0624
Operating Voltage: DC 2V- 9V Operating frequency: 85MHZ - 115MHZ Output Impedance: 50 ohms
Reference: RBD-0814
The 2021 Model is Sonoff Basic R2 Support remotely turn on or off added devices. Support Max 8 timers tasks for each added device. Works with AMAZON ALEXA Works with GOOGLE ASSISTANT Also, Work with NEST Support numerous Wi-Fi smart switches one smartphone.
Reference: RBD-0426
Power supply voltage of 2.5 V ~ 5 V Low power consumption Wide detection range: 240 nm to 370 nm Wide Angle: 130 degrees Schottky type photosensitive diode Good linear response High sensitivity
Reference: RBD-0441
Power supply voltage: DC5 ± 2V Sensitivity: 0.5V / (0.1mg / m3) The minimum detection level of particles: 0.8 m Clean air voltage: 0.9V typ. Low consumption current (Icc: MAX. 20 mA) The presence of dust can be detected by the photometry of only one pulse Enable to distinguish smoke from house dust RoboticsBD
Reference: RBD-1333
Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key. Dimensions: 56 x 80 x 17 mm.(LxWxH)
Reference: RBD-2351
HLK-LD2410C is a high-sensitivity 24GHz human presence status sensing module developed by Hi-Link Electronics. Its working principle is to use FMCW frequency-modulated continuous wave, to detect human targets in the set space, combined with radar signal processing, accurate human body induction algorithm, to achieve high sensitive human presence status...
Reference: RBD-1872
Product: Water Pump Model: AD20P-1230C Voltage: 12V Current: 350mA. Power consumption: 3.6W.
Reference: RBD-2045
Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0554
VL53L0X 3-in-1 ranging and gesture detection sensor Regulator: 5 to 2.8V range input voltage (output voltage: 2.8V) VL53L0X signal interface level shifter Serial Port PWM Output True distance measurement independent of target size and reflectance Breakout board, easy to integrate into the customer device Allows basic gesture recognition use case. RoboticsBD
Reference: RBD-1689
Professional Diamond Selector II, Gem Tester Pen Portable Electronic Diamond Tester Tool for Jewelry Jade Ruby Stone Products are being tested.
Reference: RBD-1172
Infrared Sensor Automatic Lighting Control Switch with lamp holder; convenient, safe & practical. Good solution for energy saving. You can conveniently let the light auto on/off. The switch can detect the human body's infrared, and use infrared to control the load. Easy to install. Strong anti-interference ability Suitable for corridor, toilet,...
Reference: RBD-1947
Operating Voltage: 12V DC Equipped with high-current relay 10A 250VAC / 10A 30VDC It can control both AC and DC appliances such as Solenoids, Motors, lights, fans, etc. High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection. Freewheeling diode to protect your microcontroller. Input Signal Pin connected to Burg...
Reference: RBD-0682
Microcontroller: ATmega168 or ATmega328V Operating Voltage: 2.7-5.5 V Digital I/O Pins: 14 PWM Channels: 6 Analog Input Channels: 6 DC Current per I/O Pin: 40 mA Board will run from 2V to 5V. The latest version of the LilyPad supports automatic reset for even easier programming. The back side of the LilyPad is now completely flat! RoboticsBD
Reference: RBD-0926
USB Driver: FT232 Manufacturer: Gravitech Operating Voltage (logic level): 5V 8 analog inputs ports: A0 ~ A7 14 Digital input / output ports: TX, RX, D2 ~ D13 1 pair of TTL level serial transceiver ports RX / TX Using Atmel Atmega328P-AU MCU There is a bootloader installed in it Standard 0.1” spacing DIP (breadboard friendly). Manual reset switch. Please...
Reference: RBD-1948
Channel: 8 channel Relay Operating Voltage: 5V One normally closed contact and one normally open contact Triode drive, increasing relay coil High impedance controller pin Pull-down circuit for the avoidance of malfunction Power supply indicator and Control indicator lamp Power supply and relay instructions, lit, the disconnect is off Note: Relay might be...
Reference: RBD-2039
Product Name:DY-SV5W Voice Playback Module Product Number:DY-SV5W Work Voltage:DC 5V Working Temperature range:-20℃~85℃ Working Humidity range:0%-95%RH Size :35*35*4.5mm
Reference: RBD-1081
Brand: Raspberry Pi Official
Original Raspberry Pi Product. Temperature-Controlled Fan, Delivers up to 1.4CFM of Air Flow. Comes With Aluminium Heat Sink Compatible With the Official Raspberry Pi 5 Case. Stock is available with Complete Set. Please purchase Raspberry Pi 5 Complete Set.
Reference: RBD-1670
The smallest 802.11b/g/n Wi-Fi SoC module Uses low power 32bit CPU and compatible with the application processor Main frequency up to 160MHz Built-in 10Bit high precision ADC Support UART/GPIO/PWM/ADC interface Integrate Wi-Fi MAC/BB/RF/PA/LNA
Reference: RBD-1930
Suitable for DIY & Hobby Kits, Routers, LED Strip Driver, and Home Appliances. Rated Input AC Voltage 100v-240v It comes with a 1 meter long 24 AWG cable Stabilized DC Output with Low Ripples & Interference Short Circuit & Overload Protection High Efficiency & Low Energy Consumption RoHS and BIS compliance Approved. Note: Adapter only....
Reference: RBD-1975
Brand: DFRobot
Clutch function Electronic Protection Large Torque Stable performance Accurate running angle Easy to install
Reference: RBD-2181
Professional insulated quick test hook clip High voltage flexible testing probe Comes with a 4mm socket Red and black color Compact and lightweight design
Reference: RBD-1812
11 digital input/output pins Interrupt/PWM/I2C/one-wire 1 analog input(3.2V max input) 16M bytes(128M bit) Flash External antenna connector Built-in ceramic antenna New CP2104 USB-TO-UART IC
Reference: RBD-2335
The Arduino Uno R3 Standard-Quality Edition Micro-controller : ATmega328. Operating Voltage : 5V. Input Voltage (recommended) : 7-12V. Digital I/O Pins : 14 (of which 6 provide PWM output). Analog Input Pins : 6 We are pleased to present a more cost-effective version of the Arduino Uno R3, a widely acclaimed and versatile platform for electronics...
Reference: RBD-2516
Nominal Voltage: 5V DC Current Draw: 0.6 Amps at 5V Holding Force: 2.5Kg / 5.5lb Approximate Pickup Weight: 0.45 Kg / 1 lbEver wanted to feel like Magneto? Well, now you sort of can! Bring the ferromagnetic objects in the world under your control with an Electromagnet The simplest way to make an electromagnet is to get a solenoid, pass some current...
Reference: RBD-0155
Microcontroller: ATmega328 Circuit Operating Voltage: 5V Clock frequency: 16MHz. Digital I/O Pins: 14 8 analog input port: A0 ~ A7. A pair of TTL level serial port transceiver : RX / TX. 6 PWM port: D3, D5, D6, D9, D10, D11. Support serial download.
Reference: RBD-0830
Thermocouples - K Type 800C WRN-291 200mm Rod 7.8 inch Rod/ 200mm Rod Temperature measurement range is from 0 celsius to 800 celsius degree. Screw Type
Reference: RBD-1690
ON/OFF switch button on the power adapter. Very convenient for use. 5V 3A standard power supply for Raspberry Pi 4 Model B. There is CE certification for the power adapter. Best Adapter for Raspberry Pi 4
Reference: RBD-2016
Backward compatible with USB 2.0 USS, MDIX support Jumbo packets up to 9 KB Plug and play installation Full-duplex and half-duplex operation of fast ethernet Suspend mode and remote wake up via links and magic packs
Reference: RBD-2064
TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. Note: If you want to buy the cheaper recycled SIM800L Module Click here.