Reference: RBD-2457

LM317 Adjustable Voltage Regulator Module

Regulates 4.5 – 40V input to a 1.25 – 37V output @ up to 1.5A

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-2921

2.42 inch OLED Screen LCD Display Module 128x64 SSD1309 SPI 7Pin Yellow

Operating Voltage: 3.3V Resolution: 128 × 64 pixels Communication Interface: SPI (default) Display size: 55.01 × 27.49mm Driver: SSD1309Note: The component, colour & shape of the module may vary depending on our stock rotation.

Reference: RBD-0393

JoyStick 5Pin Breakout Module For Arduino

Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD

Reference: RBD-2565

MOSFET Switch Module IRF520

Mosfet switch module on breakout board with screw terminals and pin headers. Useful for controlling high power loads (max 24V / 5A) using 3.3V / 5V logic circuits. 

Reference: RBD-2102

DIP 3 Color RGB LED Module

RGB trichromatic limiting resistor to prevent burnout PWM adjusted color mixing

Reference: RBD-1970

Brand: DFRobot

Gravity: Speech Synthesis Module V2.0 (Support English and Chinese)

Version 2.0 More natural pronunciation Fewer pronunciation errors for polyphone characters No option of speakers

Reference: RBD-1331

AC Light Dimmer Module, 2 Channel, 3.3V/5V logic, AC 50/60hz, 220V/110V

High-quality BTA16-600B TRIAC AC Voltage: 220V/110V; 50/60Hz Rated current: 5A Logic: 3.3V/5V Peak Operating Current: 8A

Reference: RBD-2658

1 Channel 12V 30A Relay Control Board Module with Optocoupler

This 1 channel 12V 30A relay control board module with optocoupler modules is compliant with international safety standards, control and load areas isolation trenches it has a single relay a genuine. The inputs of 1 Channel 12V 30A Relay Module are isolated to protect any delicate control circuitry. It can be used as a single chip module for appliance...

Reference: RBD-0306

Torobot 32 Channel USB UART Servo Motor Controller

Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android

Reference: RBD-1759

Brand: Waveshare

E-Ink Electronic E-paper Display Screen Module 200x200, 1.54inch

Display Resolution: 200 x 200 Display Screen Color: Black and White No backlight so keeps displaying last content for a long time even when the power is down Ultra low power consumption, basically power is only required for refreshing SPI interface, for connecting with controller boards like Raspberry Pi/Arduino/Nucleo, etc.

Reference: RBD-0387

Arduino SD card Module

All SD SPI pins output, MOSI, SCK, MISO, and CS. Support 5V/3.3V input. This module can handle 2GB SD cards. Size:4.7  x 3.1 cm. LED indicator. SD Card Holder. RoboticsBD Onboard 3.3V regulator (AMS1117-3.3) for +5v to 3.3V generation. 3.3V is also available as output.

Reference: RBD-1816

TTL to RS485 Converter 3.3V/5V Hardware Automatic Control Converter Module

Anti-Interference Ability Baud rate: 110 ~ 256000bps Operating Voltage: 3v  to  30VDC Compatible With Both 3V and 5V logic

Reference: RBD-1337

ESP8266 Dual WiFi Relay Module Internet Of Things Smart Home Mobile APP Remote Switch

Transmission Distance(m) :400 Relay Channel:2 Trigger Voltage (VDC): 5 Switching Voltage (VAC):250@10A Switching Voltage (VDC):30@10A Baud Rate:9600 Note: Relay might be different from the picture as per stock

Reference: RBD-2323

NeoPixel 5050 WS2812B 1Bit RGB LED with Integrated Driver

The WS2812B RGB LED Module is a small module with BIG color.  The module has a special LED on board that contains three separate LEDs – red, green, and blue – as well as a smart control IC that can individually drive each LED.  Each color has 256 intensity levels which allows the module to produce 24-bit color, or more than 16 million colors.  Each module...

Reference: RBD-2086

Momentary Tactile Push Button Module DC 5V Switch

Operating Voltage: 5V Contact Resistance : 50mΩ max (initial) Electrically Life:100,000 cycles Environment temperature: -25°C to +105°C Operating Force: 180/230(±20gf) Seal temperature:250ºC-280ºC I/O pins: 3 pins

Reference: RBD-2557

Open Smart Battery Style Digital Tube LED Battery Level Display Module

Introducing the Battery Level Display Module, a versatile and user-friendly device based on battery-style digital tube LED technology. This module features 10 light segments and incorporates the TM1651 driver chip for simplified control, requiring only two signal lines along with VCC and GND connections. It is specifically designed for displaying battery...

Reference: RBD-2919

MAX98357A I2S DAC Class D Mono Amplifier Module

This mono Class D amplifier module with a surprisingly compact form factor - less than 2cm on a side - uses a MAX98357 chip to deliver 3W of power. Its I2S input allows an easy association with a Raspberry Pi or ESP32, allowing for example to design a small portable amplified speaker.

Reference: RBD-2080

Dry Reed Pipe Magnetron Magnetic switch Module

Clean, good waveform driving ability, more than 15mA. Working voltage 3.3V-5 Output format: digital switching output (0 and 1) A  fixed bolt holes for easy installation

Reference: RBD-2442

TXS0108E 8-Ch Logic Level Converter Module

8 channels can convert up to 8 logic signals Converts voltage levels between 1.2 to 3.6V and 1.65 to 5.5V systems Bi-directional with automatic direction control Each channel operates independently Optimized for open-drain applications like I2C, but can also work in push-pull applications Output enable allows outputs to be disabled

Reference: RBD-0323

Arduino Uno R3 SMD

Microcontroller ATmega328 (SMD) – Interface CH340G Operating Voltage: 5V Input Voltage (recommended): 7-12V Digital I / O Pins 14 (of which 6 provide PWM output) RoboticsBD Analog Input Pins: 6 A programming cable is included.

Reference: RBD-0438

New ENC28J60 Ethernet LAN Network Module For Arduino

ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD

Reference: RBD-2076

5mm Two-Color LED Module

Operating Voltage:2.0v ~ 2.5v Current:10mA Diameter:5mm Color: Red + Green Beam Angle:150

Reference: RBD-1928

HC-08 Bluetooth 4.0BLE Serial Port Module

Frequency: 2.4GHz ISM. Protocol: BLE 4.0. Max transmitting power: max. 4dBm. Modulation System: GFSK. Serial Baud Rate: 1200 to 115200 bps. Reference Distance: 80 meters.

Reference: RBD-1402

NodeMCU ESP8266 Expansion Base Board

The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.

Reference: RBD-0980

NeoPixel NeoMatrix 8x8 - 64 RGB LED Pixel Matrix WS2812 5050 RGB LED

Dimensions : 66 x 66 x 3 mm. Weight : 25 gm. Supply Voltage : 5 VDC. Interface : IO . 8 x 8 = 64 RGB. Chip : WS2812.

Reference: RBD-2447

MP2315 Mini Adjustable DC-DC Step-Down Module

Ultra small module converts 4.5 – 24V input down to a 0.8 – 22V output @ up to 2A.

Reference: RBD-0948

ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi

Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V A high-quality USB cable is essential for this board to ensure sufficient current supply; otherwise, your board may not be recognized by the Windows Device Manager. Please avoid using mobile phone cables and...

Reference: RBD-2757

D4184 MOSFET Control Module

N-Channel logic compatible MOSFET with optoisolation and low Rds(on).

Reference: RBD-2396

GPS Module NEO-7M Satellite Positioning Module for Arduino with MicroUSB

GPS Module NEO-7M Satellite Positioning Module for Arduino with MicroUSB