How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: RBD-1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: RBD-245
Choose your desire Resistor value from below:
Reference: RBD-31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Arduino Etherner Shield in Bangladesh
The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet.
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet. As always with Arduino, every element of the platform – hardware, software and documentation – is freely available and open-source. This means you can learn exactly how it's made and use its design as the starting point for your own circuits. Hundreds of thousands of Arduino boards are already fueling people’s creativity all over the world, everyday. Join us now, Arduino is you!
The Arduino Ethernet Shield allows an Arduino board to connect to the internet. It is based on the Wiznet W5100ethernet chip (datasheet). The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP. It supports up to four simultaneous socket connections. Use the Ethernet library to write sketches which connect to the internet using the shield. The ethernet shield connects to an Arduino board using long wire-wrap headers which extend through the shield. This keeps the pin layout intact and allows another shield to be stacked on top.
The most recent revision of the board exposes the 1.0 pinout on rev 3 of the Arduino UNO board.
The Ethernet Shield has a standard RJ-45 connection, with an integrated line transformer and Power over Ethernet enabled.
There is an onboard micro-SD card slot, which can be used to store files for serving over the network. It is compatible with the Arduino Uno and Mega (using the Ethernet library). The onboard microSD card reader is accessible through the SD Library. When working with this library, SS is on Pin 4. The original revision of the shield contained a full-size SD card slot; this is not supported.
The shield also includes a reset controller, to ensure that the W5100 Ethernet module is properly reset on power-up. Previous revisions of the shield were not compatible with the Mega and need to be manually reset after power-up.
The current shield has a Power over Ethernet (PoE) module designed to extract power from a conventional twisted pair Category 5 Ethernet cable:
Reference: RBD-1336
ESP8266 ESP-01S 5V WiFi Relay Module Things Smart Home Remote Control Switch Phone APP ESP01 ESP-01 Wireless WIFI Module (ESP8266 is not included)
Reference: RBD-282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU
Reference: RBD-699
1.8-inch color screen,support 65K color display,display rich colors 128X160 resolution, clear display Using the SPI serial bus, it only takes a few IOs to illuminate the display With SD card slot for convenient function expansion Provide underlying libraries and rich sample programs for Arduino, C51, and STM32 platforms Military-grade process standards,...
Reference: RBD-1353
Length: 12.5 inches (Long) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: RBD-1337
5V ESP8266 Dual WiFi Relay Module Internet Of Things Smart Home Mobile APP Remote Switch
Reference: RBD-397
MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino
Reference: RBD-438
Chip board ENC28J60-I/SOThe board 25MHZ crystalThe network interface board HR911105A3.3 V power supply pinThe board size : 56 (mm) x 34 (mm)
Reference: RBD-990
XFS5152CE Speech Synthesis Module TTS Voice Module Support Encode Decode Realized English & Chinese Speech
Reference: RBD-413
SD card interface works with FAT16 or FAT32 formatted cards. 3.3v level shifter circuitry prevents damage to your SD card Real time clock (RTC) keeps the time going even when the Arduino is unplugged.
Reference: RBD-684
The TB6612FNG motor driver can control up to two DC motors at a constant current of 1.2A (3.2A peak). Two input signals (IN1 and IN2) can be used to control the motor in one of four function modes - CW, CCW, short-brake, and stop.
Reference: RBD-345
ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is a highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module.
Reference: RBD-1367
The KY-009 RGB Full Color LED SMD Module consists of a 5050 SMD LED, use with limiting resistors to prevent burnout. Compatible with popular electronics platforms like Arduino, Raspberry Pi and ESP8266. RGB full color LED Module KY-009 for Arduino, emits a range of colors by mixing red, green and blue. The amount of each primary color is adjusted using PWM.
Reference: RBD-1180
Relay Shield (ie 5V Quad Relay Module) is a small current signal control power equipment commonly used electronic module, enabling high-power single-chip control devices are widely used in SCM system to make smart home project; and can be directly plugged into the compatible the use of various types of motherboards, eliminating the patch cable troubles.
Reference: RBD-914
MAX7219 Dot Matrix Module Microcontroller 4 In One Display with 5P Line
Reference: RBD-189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: RBD-323
Arduino Uno R3 is the clone one of the latest version of Arduino Uno with an on-board CH340 usb - serial converter chip. Even there are some little differences with respect to the original one, it is almost the same in terms of usage and software. This provides you a cheaper opportunitiy to get started with Arduino boards. The microcontroller model of...
Reference: RBD-346
NXP PN532 NFC RFID Module V3 Kits Reader Writer Arduino Android Phone M92 NFC is a popular technology in recent years. We often heard this work while smart phone company such as Samsung or HTC introduces their latest high-end phones. Almost all the high-end phone in the market support NFC.
Reference: RBD-1398
This is a 12V 1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) . **Relay Brand is different from the picture as per stock
Reference: RBD-1753
INMP441 Omnidirectional Microphone Module
Reference: RBD-443
The GPRS Shield provides you a way to use the GSM cell phone network to receive data from a remote location. The shield allows you to achieve this via any of the three methods: Short Message Service Audio GPRS Service
Reference: RBD-1137
The ENC28J60 Ethernet Module uses the Microchip ENC28J60 Stand-Alone Ethernet Controller IC featuring a host of features to handle most of the network protocol requirements. The board connects directly to most microcontrollers with a standard SPI interface with a transfer speed of up to 20MHz.
Reference: RBD-399
Specification:1. "LIGHT" linked with GND, the backlight to be lit.2. Need you to compress the screen and PCB tighter, might got loose after the delivery. 3. Use a 3.3V controller, otherwise the display could be quite vague.
Reference: RBD-1772
HLK-V20 is the latest high-performance pure offline speech recognition module for a large number of pure offline control scenarios and products.It can be widely and quickly applied to smart homes, various smart small appliances, 86 boxes, toys, lamps, industrial, , Products that require voice control, such as the Internet of Things, automobiles, security...
Reference: RBD-1021
Operating voltage: 2.5V-5.5V, recommended 5VSpeaker Load: 2-8 OhmsInput and Output Connectors: Pins on 0.2" centersSize: 24 x 23 x 105 mm (L x W x H)Net weight: 3g
Reference: RBD-1349
It is another great blue backlight LCD display. As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you will be able to realize data display via only 2 wires. If you already has I2C devices in...
Reference: RBD-1762
Tesla coil is a transformer (resonant transformer) that operates on the principle of resonance.It can produce high-temperature and high-pressure plasma and can ignite, wirelessly transmit electricity, illuminate fluorescent lamps. It has wonderful arcs and is used for many fun and very interesting scientific experiments.This product is newly developed....
Reference: RBD-948
ESP32 Development Board WiFi+Bluetooth Ultra Low Power Consumption Dual Cores ESP-32 ESP-32S Board
Reference: RBD-1602
The OTA WeMos D1 CH340 WiFi Development Board ESP8266 ESP-12F is a more Powerful Arduino with WIFI support. This development platform Espressif based on the ESP-8266 is the pins of the Arduino Uno almost compatible and can even be used as some shield modules designed for the classic Arduino Uno. *No Cable
Reference: RBD-345
ESP8266 is a wifi SOC (system on a chip) produced by Espressif Systems. It is a highly integrated chip designed to provide full internet connectivity in a small package. This is a module based on ESP8266 chip. Please see supplied pinout photo and schematics for connectivity details. There is a lot of online resources available for this module.
Reference: RBD-212
B3 LIPO Battery Charger 7.4v 11.1v Li-polymer Lipo Battery Charger 2s and 3s Cells for RC LiPo Battery Brand: Build Power/ IMAX (Clone) As per stock
Reference: RBD-702
This is a 5V 1-Channel Relay interface board, Be able to control various appliances, and other equipments with large current. It can be controlled directly by Micro-controller (Raspberry Pi, Arduino, 8051, AVR, PIC, DSP, ARM, ARM, MSP430, TTL logic) . **Relay Brand is different from the picture as per stock
Reference: RBD-1162
15G Solid Rosin Welding Soldering Flux Paste High Purity
Reference: RBD-393
Specification: Brand new Color: as picture shows Size: approx. 34 x 26 x 32mm (L x W x H) Quantity: 1pc PS2 joystick joysticks standard interface module electronic building blocks and 2.54mm pin interface leads
Arduino Etherner Shield in Bangladesh
The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet.
