Reference: RBD-0104

6DOF Accelerometer Gyroscope GY-521 MPU-6050

31 reviews

Chip built-in 16bit AD converter, 16-bit data output Driver Chip: MPU6050 Operating Voltage: 3-5V DC Communication: I2C/IIC Protocol Gyro Range: ± 250, 500, 1000, 2000 °/s Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g

Reference: RBD-0555

Current Sensor ACS712-30A

5 reviews

Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A

Reference: RBD-0151

Angle Sensor Module for Arduino SW-520D

1 review

Operating voltage 3.3V-12V A fixed bolt hole for easy installation Wide voltage LM393 comparator Maximum output current: 15mA Can work on low voltages

Reference: RBD-0559

Voltage to Current Transmitter Signal Module

2 reviews

Power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA  0-5V to 4-20mA Linear Conversion

Reference: RBD-0233

Brand: SparkFun Electronics

SparkFun 9 Degrees of Freedom IMU Breakout - LSM9DS0

Description: This is the LSM9DS0, a versatile motion-sensing  system-in-a-chip that houses a 3-axis accelerometer, 3-axis  gyroscope, and 3-axis magnetometer. That’s right, 9 degrees  of freedom (9dof) from a single IC!

Reference: RBD-0562

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator

3 reviews

Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm

Reference: RBD-0288

GY-801 - Multi Sensor Board

1 review

Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v

Reference: RBD-0564

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

1 review

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-1173

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000 100A

3 reviews

Input Current : 100A Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Meet UL94-V0 flame retardant properties

Reference: RBD-0382

GY-87 10DOF MPU6050 HMC5883L BMP180 Sensor Module

1 review

3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD

Reference: RBD-1175

Current Sensor ACS712-20A

3 reviews

Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 20A Sensitivity: 100mV/A

Reference: RBD-0386

Precision Real Time Clock Module DS3231 AT24C32 I2C

29 reviews

1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.

Reference: RBD-1174

Current Sensor ACS712-5A

8 reviews

Low-noise analog signal path. Device bandwidth is set via the new FILTER pin. 5 µs output rise time in response to step input current. Small footprint, low-profile SOIC8 package. 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.

Reference: RBD-0574

Honeywell HMC5983 Temperature Compensated Three-Axis Digital Compass

3-Axis Magnetoresistive Sensors and ASIC in a 3.0x3.0x0.9mm LCC Surface Mount Package Temperature Compensated Data Output and Temperature Output Automatic Offset Compensation. RoboticsBD

Reference: RBD-1177

4-20mA Signal Generator Current Loop Simulator Tester

This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...

Reference: RBD-0664

ADXL345 Triple Axis Accelerometer Breakout

9 reviews

Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD

Reference: RBD-1344

Current to Voltage Transmitter Module

Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V

Reference: RBD-0680

9 Degrees of Freedom Breakout- MPU9250

4 reviews

Acceleration, Gyroscope, and Magnetometer Power Supply: DC3.3V-5V Chip: MPU9250 Size: 22 mm x 17 mm. Gyro range : ± 250 500 1000 2000 ° / s Acceleration range: ± 2 ± 4 ± 8 ± 16g Magnetic field range: ± 4800uT 9 DOF modules. RoboticsBD

Reference: RBD-1424

ZMCT103C 5A Range Single Phase AC Micro Current Transformer Sensor

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-0687

BMP280 Pressure Sensor Module

10 reviews

Operating Voltage: 1.71V to 3.6V – would typically be operated from 3.3V. Operating Temperature: -40 to +85 deg. Celsius (full accuracy between 0 and +65 deg. C). Peak current: 1.12mA. RoboticsBD Operating Pressure: 300 hPa to 1100 hPa. Accuracy between 700 to 900hPa and 25 to 40 deg. C: ±0.12hPa and ±1.0m.

Reference: RBD-1675

PZEM-004T V3.0 AC Digital Multifunction Meter Watt Power Volt Amp With Coil 100A

1 review

Model: PZEM-004T Operating Voltage: 80-260VAC Test Voltage: 80-260VAC Rated Current: 100A Rated power: 100A / 22000W Operating frequency: 45-65Hz Measurement accuracy: 1.0

Reference: RBD-0700

GY- BMI160 6DOF Gravity Accelerometer Sensor

1 review

Operating Voltage: 3.3V-5.5V Low Power Consumption High Accuracy Small Size

Reference: RBD-1835

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-050 50A

1 review

Input current (RMS): 50A. Work temperature: -25℃～+70℃. Storage temperature: -30℃～+90℃. Work voltage: 660V. Frequency range: 50Hz-1KHz.

Reference: RBD-0742

Motor Driver 43A BTS7960

8 reviews

Input voltage(V): 6 – 27. Maximum current(A): 43. Input level(V): 3.3 – 5. Duty cycle: 0 – 100%. Path resistance: 16 mΩ at 25°C. Low quiescent current: 7 µA at 25°C.

Reference: RBD-1836

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000 30A

2 reviews

Input Current : 0-30A Output Mode: 0-1V @ 30mA Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection Meet UL94-V0 flame retardant properties

Reference: RBD-0743

S550 Hexcopter Frame 550mm (Black)

Wheelbase: 550mm Weight: 550g/720g(without/with gimbal) Adopts S800 upward tilt arm design – Plastic injection moduling Ensures hardness and lighter weight – Brushless gimbal compatible for FPV It comes with PCB center board of soldered The arm equips support ridges for better and faster forward flight. Features pre-threaded brass sleeves.

Reference: RBD-1972

Brand: DFRobot

Gravity: Analog AC Current Sensor (20A)

Brand Gravity Analog AC Current Sensor 20A AC Current Signal Conversion Module Open Type AC Transformer Probe Included Non-contact Measurement

Reference: RBD-0797

U-Blox NEO-6M GPS Module

36 reviews

5Hz position update rate. The cold start time of 38 s and Hot start time of 1 s. Configurable from 4800 Baud to 115200 Baud rates. (default 9600). SuperSense ® Indoor GPS: -162 dBm tracking sensitivity. Support SBAS (WAAS, EGNOS, MSAS, GAGAN). Separated 18 x 18mm GPS antenna. RoboticsBD In recent years 2022, due to a shortage of chips, some of the GPS...

Reference: RBD-2071

SS49E Linear Hall Effect Sensor Module

1 review

Type: Magnetic Sensor Module Mainly Compatible with: Ardunio

Reference: RBD-0812

High Accuracy I2C MAX30105 Particle Optical Sensor Photodetectors Oximeter Module

1 review

Based on MAX30105 – heart rate, oximeter, smoke sensor Green, red, and infra-red LEDs Interface: I2C (address 0x57) Compatible with 3.3V and 5V logic levels.

Reference: RBD-2072

Linear Magnetic Hall sensor

1 review

Operating Voltage: 3.3V-5V Features wide range voltage comparator LM393 Adjustable sensitivity Signal output indicator with the retaining bolt hole, convenient installation Output form digital switch output (0 and 1 high and low level) The output effective signal is low level When there is sound, outputs low level and the signal light