- Raspberry Pi
- Mini Computer/ PC
- 3D Printer
- Arduino Shield
- Robotics Parts
- Home Automation
- Industrial Shield
- Industrial IC
- Motor Driver
- Communication Module
- Robot Platform Chassis
- 3D Printed
- Power Adapter
- PLC Programming Cable
- Tools, Hardware & Accessories
- Thermal Printer
- Solar Panel
- Battery & Charger
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Honeywell HMC5983 Temperature Compensated Three-Axis Digital Compass
The HMC5983 includes our state-of-the-art, high-resolution HMC118X series magnetoresistive sensors plus an ASIC containing amplification, automatic degaussing strap drivers, offset cancellation, and a 12-bit ADC that enables 1° to 2° compass heading accuracy. The I²C or SPI serial bus allows for easy interface.
Store Pickup Available!
Immersion Gold Process gilded Pin interference
HMC5983 high-precision triaxial compass magnetic field sensor with temperature compensation
Means of communication: IIC / SPI optional
Power supply: DC3-5V
With temperature compensation data output;
Automatic offset compensation;
Maximum 220HZ output frequency
Heading angle accuracy of 1-2 degrees.
PCB size: 15mm * 24mm
Digital Electronic Weighing SensorScale 1Kg Weight Load Cell 3-12V DC
Description: This is RGB and Gesture Sensor, a small breakout board with a built in APDS-9960 sensor that offers ambient light and color measuring, proximity detection, and touchless gesture sensing. This is, in fact, the same sensor that the Samsung Galaxy S5 uses and is probably one of the best gesture sensors on the market for the price.
2.8V Regulator - Provides the required 2.8V for the sensor I2C Level Shifter - Provides logic level conversion from 2.8V to VCC 3-in-1 Module IR Emitter Range Sensor Ambient Light Sensor Measures absolute range up to 10cm Gesture Recognition I2C Interface Two Programmable GPIO Sharp Sensor Board Layout
This is a pre-wired and waterproofed version of the DS18B20 sensor. Handy for when you need to measure something far away, or in wet conditions. While the sensor is good up to 125°C the cable is jacketed in PVC so we suggest keeping it under 100°C. Because they are digital, you don't get any signal degradation even over long distances!
Angle Sensor Module for Arduino High-sensitivity angle sensor SW-520D Comparator output, clean signal, great waveform, strong driving ability, more than 15mA Distribution positioner sensitivity adjustment Working voltage: 3.3V~12V Output form: Digital switching output (0 and 1) With fixed bolt hole for easy installation
Description: Type K Type. Mounting thread: M6 Temperature Range:0-600°C. Thread Diameter:6mm / 0.23". Internal Insulation:Fibreglass. External Shielding:Metal Shield. Total Length:1M / 39". Fork Terminal Spacing: 3.5mm / 0.13". Color: As Picture Shown. 10mm thread sensor for accurate measurement.
Gas Sensor(MQ9) module is useful for gas leakage detection (in home and industry). It is suitable for detecting LPG, CO, CH4. Due to its high sensitivity and fast response time, measurements can be taken as soon as possible. The sensitivity of the sensor can be adjusted by using the potentiometer.
VOC gas sensors are used to detect formaldehyde, toluene, benzene, etc., is a type of semiconductor sensors, it is widely used in ventilation, ventilation fans, air filters, hood, hood and other equipment. With high sensitivity and stability, able to detect more than 0.1ppm gas, air suitable for detecting a variety of volatile organic components...
The W1209 is an incredibly low cost yet highly functional thermostat controller. With this module (HCTHER0006) you can intelligently control power to most types of electrical device based on the temperature sensed by the included high accuracy NTC temperature sensor. Although this module has an embedded microcontroller no programming knowledge is...
01S Vibration Sensor Module vibration Analog Output Sensitivity LM393Size: 41 * 15 * 12.5mm The main chip: LM393, vibrating probe Operating voltage: DC 3-5V Main features: Has a signal output instructions; With analog and TTL-level signal output signal; Output valid signal is high, the light goes out; Adjustable sensitivity (fine-tuning); Vibration...
CCS811 Carbon Monoxide CO VOCs Air Quality Digital Gas Sensor Total Volatile Organic Compound (TVOC) sensing from 0 to 1,187 parts per billion eCO2 sensing from 400 to 8,192 parts per million Five Operating Modes Integrated MCU Onboard Processing Standard I2C Digital Interface Optimized Low-Power Modes Optional NTC Thermistor Pins
HX1838 NEC Code Infrared Remote Control Module DIY Kit
The FLiR Dev Kit includes a breakout as well as a Lepton® longwave infrared (LWIR) imager. With this kit you will be able to be able to bring FLiR’s thermal imaging reliability and power to your Arduino, Raspberry Pi, or any ARM based development tool all in an easy to access breadboard friendly package. Flir Lepton Installation Instruction 1 Flir Lepton...
Liquid Suspended Particles Turbidity Sensor Detection Module Kit
The Leap Motion Controller tracks both hands and all 10 fingers with pinpoint precision and incredible speed. Setup is easy, just plug into your PC or Mac and launch Airspace, your home for Leap Motion apps. Play, create, and explore in a whole new way!In Airspace, the Leap Motion App store,
FPM10A Optical Fingerprint Reader Sensor Modules Connect RoboticsBD Fingerprint Shield on top the Arduino Uno R3 Install Adafruit Fingerprint Library (Check Download Tab) Upload this code to Arduino Uno Board (Arduino Code SFG Demo) Run SFG Demo V2.0 Windows Test Software as Administrator