Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0313
Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
Reference: RBD-0384
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 320 mA Display Dimensions: 32x32x6 (LxWxH) mm PCD Dimensions: 50×32 (LxW) mm Soldering is required
Reference: RBD-0280
Tie-points: 170 (10×17) Size: 48 x 35 x 10 mm(LxWxH). Use: experimental, testing, robot Matching jumper, diameter 0.8mm Phosphor bronze nickel plated spring clips Accepts a variety of wire sizes (29-20 the AWG) **1 pcs Random Color
Reference: RBD-0399
Power supply voltage: 2.7 V-3.3 V/5 V Data interface level: 2.7-5V. Resolution: 84 x 48 pixel Backlight power supply voltage: highest 3.3 V. Backlight: Blue. RoboticsBD Note: Current stock is tested by us.
Reference: RBD-0438
ENC28J60 Ethernet Module HanRun HR911105A Ethernet port 5V supply voltage 100% Genuine ENC28J60 Chipset, compatible with Arduino etc. 25MHz Crystal. Standard HanRun HR911105A Ethernet Interface. RoboticsBD
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-0395
Input voltage range: 4V-38V DC Output voltage range: 1.25V-36V DC adjustable. Output current: 0-5A. Output power: 75W. High efficiency up to 96% The built-in thermal shutdown function Built-in current limit function In-Built output short protection function. RoboticsBD
Reference: RBD-0702
It has a relay status indicator led Power LED(Green), 8 relay status indicator LED(Red) Relay control interface by single-chip IO. Low-level suction close, high-level release. Easy to use, simple 3 line structure. Note: Relay might be different from the picture as per stock
Reference: RBD-0566
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Reference: RBD-0699
Display Size: 1.8″ Driver IC: ST7735 Input Voltage (V): 3.3 to 5 Pixel Resolution: 128 x 160 Interface Type: SPI
Reference: RBD-0690
The main chip: ISD1820. Operating Voltage: DC 3V-5V. Loudspeaker: 8Ω, 0.5W. An easy to use 10 seconds of voice recording. High-quality, natural voice restored. Can be used as a propaganda module. With looping, jog playback, single-pass play function.
Reference: RBD-0730
The performance is much higher than LM2577. Non-isolated Boost converter. It has a non-synchronous rectifier. Low ultra wide input voltage 3 v ~ 32 v, the best is 5 ~ 32 v working voltage range; Low ultra wide output voltage 5 v ~ 35 v;
Reference: RBD-0981
Low power device. DTMF decoder chip. Band-split filter. Digital decoding functions. Modem interfaces. Mobile radios.
Reference: RBD-0737
Power supply:5VDC/160mA Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-0985
Stackable design, easy to plug into the ARDUINO development board. Coupled with the Arduino Bluetooth Bee Bluetooth module, and other Bluetooth devices can communicate Wirelessly. 3.3v and 5v dual power output. 3.3v and 5v IO compatible. USB2.0 protocol.
Reference: RBD-0987
Compatible with Arduino NANO All digital and analog pins breakout Compact size; External power supply current support Leads all pins out, convenient for wiring and doing experiments.
Reference: RBD-1137
Fully Compatible with 10/100/1000Base-T Networks Integrated MAC and 10Base-T PHY Supports One 10Base-T Port with Automatic Polarity Detection and Correction Supports Full and Half-Duplex modes Programmable Automatic Retransmit on Collision Programmable Automatic Rejection of Erroneous Packets SPI Interface with Clock Speeds Up to 20 MHz For Arduino, SPI,...
Reference: RBD-0765
Holds 4 AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 62 x 58 x 15 Weight: 15 gm Material: Plastic Internal Connection: Series
Reference: RBD-0836
Model: 14500 Type: Li-Ion Battery Mark Capacity: 850mah Nominal Voltage: 3.7v Color: Blue Weight: 17g Rechargeable Battery: Yes Note: It's a clone battery so the ampere couldn't be guaranteed.
Reference: RBD-1336
Onboard Module: ESP8266 wifi module; in AP mode it can connect with 5 Clients at the same time Operating Way: cellphone carried on wifi module; cellphone and wifi module carried on the same router, and use the APP to control relay Transmission Distance : 400m (max) Relay : 5V,10A/250V AC 10A/30V DC Baud Rate: 9600. Diode effusion protection; Short...
Reference: RBD-1398
Brand new and high quality. 1-Channel Relay interface board, Equipped with high-current relay : 15A @ 125V AC or 10A @ 250V AC Standard interface that can be controlled directly by microcontroller (Arduino, 8051, AVR, PIC, DSP, ARM) **Relay Brand is different from the picture as per stock
Reference: RBD-1402
The perfect solution for breaking out the pins from Lua V3 Nodemcu. Lead-out all the IO ports of the ESP-12E development board Lead out the pins of 5V and 3.3V power supply Convenient to connect with peripheral modules Onboard 5V / 1A DC-DC step-down converter circuit Onboard power indicator With DC power jack 6-24V.
Reference: RBD-1417
SMD-MAX7219-MODULE A single module can drive an 8 * 8 common cathode lattice Module Operating voltage: 5V. Module with input and output interfaces Supports multiple modules cascade Led color: Red
Reference: RBD-1575
Part Number: G3MB-202P Power supply:5VDC/160mA Trigger Voltage (VDC):5 Switching Voltage (VAC):240@2A Isolation: Phototriac
Reference: RBD-1041
PCB Size: 60 x 20 x 13.5 (LxWxH)mm. Color: red, yellow, green LED Size: 10mm x 7. Brightness: Normal brightness. Voltage: 5V. Interface: common cathode red yellow green control.
Reference: RBD-1602
Microcontroller: ESP8266EX Operating Voltage: 3.3V Digital I/O Pins: 11 (all I/O pins have interrupt/PWM/I2C/one-wire capability, except for D0) Analog Input Pins: 1 Flash Memory: 4MB On-Board Switching Power Supply: Input Voltage Range: 9V to 12V Output: 5V at 1A Max
Reference: RBD-1738
Operating Voltage : 1.5 ~ 15V DC Working Current: Less than 25mA Tone Generation Range : 1.5 ~ 2.5kHz Dimensions (LxWxH): 26 x 15 x 11 mm
Reference: RBD-1762
Input voltage(V): 9-12 It can produce high-temperature PCB board size(cm): 3.1 x 4 It is convenient for fans to install high efficiency Weight(g): 20This product is shipped as unassembled and requires soldering to be completed. You will need to do the soldering yourself.
Reference: RBD-1303
Cell Quantity: 6 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC Dimensions: 92 x 57 x 15 mm
Reference: RBD-1810
Motor Power Range: 4.5V ~ 36V Control supply range: 4.5V ~ 9V Logical operating current Iss: ≤60mA Driving part of the work current Io: ≤1.2A Maximum power dissipation: 4W (T = 90 ℃) Operating temperature : -25 ℃ ~ + 125 ℃ Drive Type: Dual high-power H-bridge driver
Reference: RBD-1329
Current: 1A; Voltage : AC 220V / 380V Thread Dia(Approx) : 11mm/0.43" Overall Size(Approx) : 14 x 20mm/0.55" x 0.78"(D*L) Weight : 16g; Package Content : 2 x Keylock Switch