Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0155
Microcontroller: ATmega328 Circuit Operating Voltage: 5V Clock frequency: 16MHz. Digital I/O Pins: 14 8 analog input port: A0 ~ A7. A pair of TTL level serial port transceiver : RX / TX. 6 PWM port: D3, D5, D6, D9, D10, D11. Support serial download.
Reference: RBD-1523
Microcontroller: ATmega328P Circuit Operating Voltage: 5V Clock frequency: 16MHz. 6 PWM port: D3, D5, D6, D9, D10, D11. Use For Atmel Atmega328P-AU microcontroller. Support serial download. Support 9V battery. A pair of TTL level serial port transceiver : RX / TX.
Reference: RBD-0838
ATMEGA32U4 running in 5V / 16MHz Support Arduino IDE V1.0.1 Micro USB interface programming on the board Four 10-bit ADC pin 12 digital I / O (5 PWM capability) Rx and Tx hardware serial connection. RoboticsBD
Reference: RBD-2053
ATMEGA32U4 running in 5V / 16MHz Support Arduino IDE V1.0.1 Micro USB interface programming on the board Four 10-bit ADC pin 12 digital I / O (5 PWM capability) Rx and Tx hardware serial connection. RoboticsBD
Reference: RBD-0311
Working Voltage: 5 to 18V DC (min tested working voltage 4.5V). RoboticsBD Max current draw: 15mA @ 5V. Working Flow Rate: 1 to 30 Liters/Minute. Maximum water pressure: 2.0 MPa. Flow rate pulse characteristics: Frequency (Hz) = 7.5 * Flow rate (L/min). RoboticsBD
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-0414
A probe by new original installation import DS18B20 temperature sensor chip. RoboticsBD Chip each pin use heat shrinkable tube to prevent short circuit, internal sealing glue, waterproof, moistureproof. Stainless steel tube encapsulation waterproof moistureproof prevent rust. Stainless steel shell (6 * 45 mm), lead length 100 cm (shielding wire) use...
Reference: RBD-1761
USB Type: Type-A to Type-B Weight: 80 gm. Length: 1m / 3.2Feet Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-1807
Altera Cyclone IV FPGA EP4CE6E22C8N EP4CE6 Development Board
Reference: RBD-0491
Sensor Type: Inductive Sensing Distance: 0.197" (5mm) Output Type: NPN-NO, 3-Wire Response Frequency: 400Hz
Reference: RBD-1808
Model: F407VE-512K STM32F407VET6 development board F407 microcontroller learning board STM32 system board
Reference: RBD-0492
Proximity-sensing / Diffuse Type Voltage: DC 6-36V Current: 300mA Sensory Distance: 5mm
Reference: RBD-0523
Module Power: 5.00V Module Size : 43 x 32mm(1.69×1.26″) Measuring Range :0 – 14PH Measuring Temperature: 0 – 60 ℃ Accuracy : ± 0.1pH (25 ℃)
Reference: RBD-0550
Supply Voltage: 4.5 – 5.5 V. Current : <40 mA. Digital Interface : 5V TTL level for UART interface and GPIO. Support maximum 80 voice commands, with each voice 1500ms (one or two words speaking). Maximum 7 voice commands effective at same time. Arduino library is supplied. User-control General Pin Output. RoboticsBD
Reference: RBD-0575
Main color: Yellow Measure range: 0.00-14.00pH Resolution: 0.01pH Accuracy: ±0.05pH Calibration: two points automatic calibration
Reference: RBD-0659
Operating voltage: 4.5V to 5.0 V Supply current: 150 mA Output format: 8 Digital voltages. Optimal sensing distance: 3 mm. Maximum recommended sensing distance: 6 mm Uses 8 sensors for best resolution Comes with easy to use digital outputs that can be connected directly to microcontrollers Sample Programming Code is available. RoboticsBD
Reference: RBD-0663
Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD
Reference: RBD-0664
Supply Voltage: 3.3 V/ 5V. Interface Type: I²C, SPI. Sensing Range: ±2g, ±4g, ±8g, ±16g. Sensitivity X: 28.6 LSB/g. Sensitivity Y: 31.2 LSB/g. Sensitivity Z: 34.5 LSB/g. Ultra Low Power: 40µA in measurement mode, 0.1µA in standby@ 2.5V. Free-Fall Detection. Tap/Double Tap Detection. RoboticsBD
Reference: RBD-0688
Wide input supply (2.5 V to 12V) Easy to integrate (V+, GND, and Data) The device in deep sleep mode when Data pin is grounded Very small dimension.
Reference: RBD-0813
Operating Voltage: 5VDC. Current: 30mA (MAX). Operating temperature: -30 ° C to 80 ° C. Compatible with Arduino, Raspberry Pi, AVR, PIC, etc. Measuring Range: 0 ~ 1000 NTU.
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-1018
Dimensions: 75 x 13 x 13 mm (L x W x H) Range: 5 kg Cable Length: 18 cm Fitting ScrewHole Size: M3 Rated output: 1.0 0.1mV / V Nonlinear: 0.05% F.S Hysteresis: 0.0% F.S Repeatability: 0.05% F.S
Reference: RBD-1049
Operating voltage: 5V Provide both digital and analog output Adjustable sensitivity Output LED indicator Compatible with Arduino TTL Compatible Bolt holes for easy installation
Reference: RBD-1172
Infrared Sensor Automatic Lighting Control Switch with lamp holder; convenient, safe & practical. Good solution for energy saving. You can conveniently let the light auto on/off. The switch can detect the human body's infrared, and use infrared to control the load. Easy to install. Strong anti-interference ability Suitable for corridor, toilet,...
Reference: RBD-1347
TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.
Reference: RBD-1348
Easy to install. Automatic, convenient, safe and practical. It has the function of power and detection indication. The motion sensor can identify day and night automatically.
Reference: RBD-1374
Model: AM2301. Supply voltage: 3.3 ~ 5.2 V DC. Signal output form: Digital signal output. Temperature measurement range: -40 ~ +80 ºC. Temperature measurement precision: ± 0.5ºC Humidity range: 10%~90%RH. Humidity measurement precision: ±3%RH.
Reference: RBD-0551
Weighing Range: 0 ~ 1 kg. Rated Output: 1.0 ± 0.1mV / V. Non Linear Output: ± 0.03% F.S. Input Impedance: 1066 ± 10% Ω. Output Impedance: 1000 ± 10% Ω. Insulation Resistance: 2000 MΩ. RoboticsBD
Reference: RBD-1422
Processor: NXP LPC4330, 204 MHz, dual core Image sensor: Aptina MT9M114, 1296×976 resolution with integrated image flow processor Lens field-of-view: 80 degrees horizontal, 40 degrees vertical Power consumption: 140 mA typical Power input: USB input (5V) or unregulated input (6V to 10V) RAM: 264K bytes Flash: 2M bytes
Reference: RBD-1423
Brand: Raspberry Pi Official
Sony IMX477R stacked, back-illuminated sensor. Resolution: 12.3 megapixels. Compatible with Raspberry Pi 1/2/3/4 boards Output: RAW12/10/8, COMP8 Back focus: Adjustable (12.5 mm–22.4 mm) Lens standards: C-mount, CS-mount (C-CS adapter included) IR cut filter: Integrated Wide Field of View suitable for CCTV applications Suitable for macro photography...
Reference: RBD-1672
Model Number: P06 Product Name: PIR Sensor Indoor Communication: greater than 20 Meters Detect Angle Side View: 128 degrees Detect Angle Down View: 128 degrees Detect distance: 10 Meters<