Reference: RBD-0234

Brand: SparkFun Electronics

LCD Cape - pcDuino V3 (1024x600 7" LVDS)

Description: This is a 7" LVDS LCD Cape for the pcDuino V3  with a 1024x600 screen resolution and capacitive touch from  LinkSprite. This massive screen is a great addition for the  pcDuino V3 that compliments its extreme versatility as a mini  PC development platform. 

Reference: RBD-0276

INA125P IC

1 review

LOW QUIESCENT CURRENT: 460µA PRECISION VOLTAGE REFERENCE: 1.24V, 2.5V, 5V or 10V SLEEP MODE LOW OFFSET VOLTAGE: 250µV max LOW OFFSET DRIFT: 2µV/°C max

Reference: RBD-0344

Weighing Sensor 24 Bit Load Cell Amplifier HX711

13 reviews

Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD

Reference: RBD-0412

PICkit3 Microchip MPLAB PICkit 3 PIC In-Circuit Programmer Debugger for PIC and dsPIC Flash Chips

Microchip's PICkit3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. The MPLAB PICkit3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price.

Reference: RBD-0383

ADS1115 16 Bit I2C 4 channel ADC Module

1 review

Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference

Reference: RBD-1101

5V Micro USB Tiny AVR ISP USBTinyISP Programmer Module For Arduino IDE Bootloader ISP Microcontroller

1 review

Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB

Reference: RBD-0385

MCP23017 I2C 16 Input/Output Port Expander

2 reviews

IC Name: MCP23017 Package/Case: DIP-28

Reference: RBD-0397

MCP2515 CAN Bus Module TJA1050 Receiver SPI Module For Arduino

1 review

Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...

Reference: RBD-0560

MAX485 RS-485 Module TTL to RS-485 module for Arduino

5 reviews

On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...

Reference: RBD-0695

MAX31865 SPI PT100/PT1000 RTD-to-Digital Converter Board

Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:

Reference: RBD-1700

Brand: Waveshare

ST-LINK V2 Mini- STM Programmers & Debuggers

Mini ST-LINK/V2  Small single board Extreme low cost solution  In-circuit debugger/programmer  STM8 STM32.

Reference: RBD-2142

CH340C WIFI Module Adapter Download Debug for ESP8266 ESP-01/01S

2 reviews

Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.

Reference: RBD-1344

Current to Voltage Transmitter Module

Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V

Reference: RBD-2311

USB To Serial Cable TTL 4 Pin Rs 232 UART Converter Adapter Programming Module

1 review

USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.

Reference: RBD-2315

Pogo Pin Probe Clip - 6 Pins with 2.54mm

1 review

Pin Pitch: 2.54mm Probe model: P75-E2 (pointed tip) Needle diameter: 1.3mm Needle sleeve model R75-3W Row pin number: 6Pin Row Number: Single row space between: 2.54mm

Reference: RBD-2362

CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit...

Reference: RBD-2412

USB ASP AVR Programming Device for ATMEL Processors Arduino

1 review

Compatible Chips:ATMega Series Tiny Series Classic Series CAN Series PWM Series You can also use this to recover your Arduino Bootloader

Reference: RBD-2413

FTDI Basic Breakout USBTTL 6PIN 5V Module Fio/Pro/RGB/Lilypad Programmer

Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...

Reference: RBD-2416

WEMOS CH340G Breakout 5V 3.3V USB to Serial Module

5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver

Reference: RBD-2425

Shielded Blue USB Type-C Cable 30cm for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-2427

USB Type-C Cable 1meter for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-2463

Programmer Testing IC Test Clip Black SOIC8/SOP8 Flash Chip IC Test Clamp

The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...

Reference: RBD-2655

ST-LINK/V2 CN In-Circuit Debugger/Programmer for STM8 and STM32

1 review

5V power supplied by a USB connector USB 2.0 full speed compatible interface USB standard A to mini B cable 1.65V to 5.5V application voltage supported on SWIM interface SWIM low speed and high-speed modes supported Made in China This product is a clone and might not support STM32Cube.

Reference: RBD-2714

ST-LINK V2.1 Emulator Debugger Programmer for STM32

The ST-LINK V2.1 emulator offers comprehensive support for all STM32 models, providing versatile functionality for development and debugging tasks. This product is a clone and might not support STM32Cube.

Reference: RBD-2746

QL2006 USB & RS232 PIC ICSP Programmer Emulator for Microchip MCU Programming

QL-2006 programmer is the high-speed programmer designed specially for development and production programming of PIC single chip microcomputer (SCM) by QLS Electronic Technology Co., Ltd. The product is featured with small volume, low power consumption, high reliability as well as easy and convenient operation.QL-2006 is applicable for almost all...

Reference: RBD-1834

PT100 to 0-5V Converter PCB-mounted PT100 to 0-10V Conversion Module RTD PT100 to Voltage Signal Conditioner

PT100 to 0-5V Converter Voltage Signal Conditioner PCB-mounted

Reference: RBD-1870

RS485 To TTL Module Stable UART Serial Port To RS485 Converter Function Board

Compatible with 3.3V and 5.0V power supply. Compatible with 3.3V and 5.0V signal.  Semi-hole pads, onboard module, thin PCB, having a thickness of 0.8mm.  Has RXD, TXD signal indicator light, monitor send and receive status.

Reference: RBD-1920

Programmable Relay Timer Module USB Smart Home Controller

Compared with electromagnetic relay products, the service life is longer. This product can realize fast switching of the circuit, and the number of switching is unlimited. Most equipment can use this product as it is very convenient; The interface is clear and simple, powerful, easy to understand, and almost meets all your needs. The module is featured...

Reference: RBD-0321

PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃

New PT-100 Temperature Sensor AvailableClick Here PT100 Platinum Resister Temperature Sensor Waterproof Probe -20℃ ~ 450℃

Reference: RBD-0965

Carlo Gavazzi Solid State Relays, RJ1A Series

Carlo Gavazzi Solid State Relays, RJ1A Series Item# RJ1A23D20U SSR SOLMINI 230V 20A 5-32VDC U

Reference: RBD-2056

PT-100 RTD Temperature Sensor 3 Wire 50cm

Mounting form Polish rod probe The Probe material: Stainless steel Probe diameter: 4mm Length of the probe: 30mm Cabel material Silver plated copper (not insulated), PTFE Silver plated copper (Waterproof, insulated) Accuracy ±(0.3°C+0.5%|t|) Thermal response time: <0.5s

Reference: RBD-2292

SN65HVD230 CAN Board Network Transceiver Evaluation Development Module

Onboard CAN transceiver SN65HVD230 Powered from 3.3V Features ESD protection Connecting MCUs to the CAN network Compatible with PCA82C250