Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-2436
Brand: Creality Official
Creality Ender-3 V3 SE 3D Printer Max printing speed of 250mm/s and 2500mm/s² acceleration Auto leveling with CR Touch & Strain Sensor for precise prints "Sprite" Direct Extruder for PLA, PETG, and flexible TPU Stable Dual Z-axis and Y-axis Dual Linear Shafts for reliable printing Auto filament loading and unloading for easy filament changes
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-2437
Brand: Creality Official
Build area: 300 x 300 x 400 mm Maximum print head temperature: 300°C Maximum bed temperature: 100°C Communication: WiFi, USB Supported materials: PLA, ABS, PETG, TPU, PA, and carbon fiber composites.
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-1733
Brand: Creality Official
Built-in WIFI function: Remote control printing anytime, anywhere; A Bit More Intelligence Ultra-silent Design: 32 Bit Mute Board and Mute Fan Design; Intelligent Auto-leveling: V2.0 Auto leveling way, is the same with CR-6 SE. Screen Protection & Auto-shutdown;. Safe and worry-free save energy and power. 6-steps to assemble 8 minutes to complete,...
Reference: RBD-1138
Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v
Reference: 1403
Brand: Creality Official
Replaced with New Version Creality Ender-3 V3 SE 3D Printer. Click Here
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: 1404
Brand: Creality Official
Modeling Technology: FDM(Fused Deposition Modeling) File Formats: STL/OBJ/AMF Slicer Software: Creality Slicer/Cura/Reptier-Host/Simplify3D Print Speed: 80-100mm/s Resume Print Function: Yes Printing Size: 235x235x250mm
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: 1375
Brand: Anycubic
Technique: LCD-based SLA Printing Speed: 30mm(H)/hour Power: 30W
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: 1316
Tougher and stronger Less warping (about 0.4% compared to over 8% in regular ABS) Prints smoother & smoother printed objects Better scratch, heat and oil resistance Can be polished using acetone Can be easily colored.
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: 1315
Great bio-compatibility, excellent transparency and environment-friendly Low shrinkage, good round shape Accurate diameter (±0.02mm) Easy to print with stable printing performance Various colors are available 100% bio-degradable and FDA food safety approved
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: 1391
TPU rubber based Material. Very flexible and elastic. Shore A Hardness at 87A. Tensile Strength 52 MPa.
Reference: RBD-1255
Integrated 0.96″ OLED Micro USB connection Compatible with Arduino Compatible with NodeMCU(Lua for ESP8266) Input Power 5V Compatible for Arduino Compatible with NodeMCU(Lua for ESP8266)
Reference: 1392
PETG Filament Plastic For 3D Printer 1.75mm1KG/Roll Compatible with Anycubic, Creality. Temperature: 205-230 °C Bed Temperature: 60-80 °C
Reference: 1317
TPU rubber based Material. Very flexible and elastic. Shore A Hardness at 87A. Tensile Strength 52 MPa.
Reference: RBD-1671
ESP32 Bluetooth Wi-Fi development board, support NodeMCU / Arduino DHT11 temperature and humidity sensor CP2104 communication chip USB TO TTL Micro USB port Soil probe (long) soil temperature and humidity detection module 18650 Lithium Battery Holder Powered (Battery is not included)
Reference: RBD-1386
Brand: Anycubic
Wavelength(nm): 395-405 Color: Black Density(g/m^3): 1.08-1.13 Hardness(Shore D):79.0 Tensile Strength(MPa): 46-67 Elongation at Break(%):28-35
Reference: RBD-1412
Chipset :ESPRESSIF-ESP32 240MHz Xtensa® single-/dual-core 32-bit LX6 microprocessor FLASH: QSPI flash 4MB / PSRAM 8MB SRAM:520 kB SRAM Button: Reset USB to TTL: CP2104 Modular interface: UART,SPI,SDIO,I2C,PWM,TV PWM,I2S,IRGPIO On-board clock:40MHz crystal oscillator Working voltage:2.7V-3.6V Working current: About 70mA
Reference: RBD-0579
Quad-band 850/900/1800/1900MHz GPRS multi-slot class12 connectivity: max. 85.6kbps(down-load/up-load) GPRS mobile station class B Controlled by AT Command (3GPP TS 27.007, 27.005 and SIMCOM enhanced AT Commands) Supports charging control for Li-Ion battery Supports Real-Time Clock Integrated GPS/CNSS and supports A-GPS Low power consumption, 10mA in sleep...
Reference: RBD-1227
Object Scanning Device with USB 2.0 Interface / CMOS Sensor
Reference: RBD-0443
Based on SIMCom‘s SIM900 Module Quad-Band 850 / 900/ 1800 / 1900 MHz - would work on GSM networks in all countries across the world. Control by AT commands - Standard Commands: GSM 07.07 & 07.05 | Enhanced Commands: SIMCOM AT Commands. Short Message Service - so that you can send small amounts of data over the network (ASCII or raw hexadecimal).
Reference: RBD-0815
Input Voltage: 100-240 V AC. Temp: 160~230 Deg settable. Filament: 1.75 mm PLA or ABS. This 3D Pen is designed for the freehand drawing of 3-Dimensional objects Adjustable output speed, temperature Create projects horizontally or vertically Every 3d pen will be checked and tested on our lab before shipping, so you will not received "intact" package. No...
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-2064
TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. Note: If you want to buy the cheaper recycled SIM800L Module Click here.
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
Reference: RBD-1557
USB communication, no need write code Support PC software automation Double antenna Support quad-band, universal worldwide Support 2G/3G/4G Automatically connect to the network Adaptive frequency