Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0165
Description: This is a powerful logic analyzer in a very small anodized aluminum package from Saleae Logic. We absolutely love the simplistic, sleek design with light-weight software and a high-quality finish. Who needs 50+ connections when you’re troubleshooting I2C? With USB connectivity, you can analyze up to 8 digital waveforms and timing information...
Reference: RBD-0268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: RBD-0390
Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).
Reference: RBD-0180
Brand: SparkFun Electronics
Description: This is the same product as the Makey Makey Standard Kit. The difference is this version comes in fancy clamshell packaging meant for our distributors that need it. Regular customers are welcome to order, but we want to limit the amount of extra packaging finding its way into the trash heap.
Reference: RBD-0218
High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-1163
The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.
Reference: RBD-0234
Brand: SparkFun Electronics
Description: This is a 7" LVDS LCD Cape for the pcDuino V3 with a 1024x600 screen resolution and capacitive touch from LinkSprite. This massive screen is a great addition for the pcDuino V3 that compliments its extreme versatility as a mini PC development platform.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0304
Uni-T UTD2102CEL 1G Digital Storage Oscilloscope 100MHz Wide Screen. RoboticsBD
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-2182
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below.
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V
Reference: RBD-1346
Model: SG92R Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 2.5kg-cm
Reference: RBD-0720
Temperature detection of the two-dimensional area: 8 × 8 (64 pixels). Digital output (capability of temperature value output). Compact SMD package (adaptively to reflow mounting). RoHS compliant. RoboticsBD
Reference: RBD-0336
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 54 Torque: 40KG.CM
Reference: RBD-1518
Operating Voltage: DC 4.8-6V Offer 3 modes to check servos or ESC The Manual Mode allows you to turn the knob to different speeds and check the reaction time The Neutral mode makes the servo go back to the neutral point The Automatic ’’Window Wiper’’ Mode makes the servo swing like a window wiper in the largest angle possible Connect to up to 3 servos...
Reference: RBD-0363
12V High Torque Turbo Worm Gear DC Motor with Metal Gearbox 54 RPM-45KG.CM Torque Model: JGB37-550 RPM: 100 Torque: 35KG.CM
Reference: RBD-1528
Input: 1S-8S Battery Battery type: Lipo/LiFe/Li-ion/LiMn It has a Buzzer Alarm for low voltage indication. Useful for measuring each cell voltage. Cell Voltage Display Range: 0.5v-4.5v Total Voltage Display Range: 3.7-36v Alarm set values: Off or 2.7-3.8v
Reference: RBD-1918
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-4.5V
Reference: RBD-1932
Rated voltage: 5 VDC. Port: Digital quantity. Fixed hole:3mm. Pitch:15mm. Drive: MOS tube high-level trigger, low-level cutoff. Compatible with UNO R3/ Mega2560.
Reference: RBD-2163
Built-in encoder Average output up to 420 pulses per revolution The brass faceplate has two mounting holes threaded Long D profile metal output shaft (0.354"/9.0 mm)
Reference: RBD-0101
Suitable for multimeters Ideal tool for electronic work Suitable for precision circuit board line measurement, micro capacitance measurement, especially suitable for excellent technology and more precise chip capacitance measurement This product can be connected to a multimeter to measure SMD components such as resistors, capacitors, etc. When the...
Reference: RBD-2177
Easy-to-use tool Small in size Color: Random Quantity: 1 pcs Weight: 0.026 kg Dimensions: 5 × 5 × 5 cm Note: You will receive random color.