Reference: RBD-0234

Brand: SparkFun Electronics

LCD Cape - pcDuino V3 (1024x600 7" LVDS)

Description: This is a 7" LVDS LCD Cape for the pcDuino V3  with a 1024x600 screen resolution and capacitive touch from  LinkSprite. This massive screen is a great addition for the  pcDuino V3 that compliments its extreme versatility as a mini  PC development platform. 

Reference: RBD-0390

12V 37GB550 Gear Motor High Torque 60 RPM

3 reviews

Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).

Reference: RBD-0218

High Torque Gear Motor 12V, 50 RPM

High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM

Reference: RBD-0412

PICkit3 Microchip MPLAB PICkit 3 PIC In-Circuit Programmer Debugger for PIC and dsPIC Flash Chips

Microchip's PICkit3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. The MPLAB PICkit3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price.

Reference: RBD-1101

5V Micro USB Tiny AVR ISP USBTinyISP Programmer Module For Arduino IDE Bootloader ISP Microcontroller

1 review

Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB

Reference: RBD-0986

4x4 Keypad - 16 Key - Matrix Membrane Type

17 reviews

Ultra-thin design & adhesive backing provides easy integration to any project. Excellent price-performance ratio. Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting.

Reference: RBD-0402

3×4 Flexible Keypad

8 reviews

Ultra-thin design & adhesive backing provides easy integration to any project Excellent price-performance ratio Easy communication with any microcontroller 5 pins 2.54mm pitch connector, 4x 4type 16 keys. Sticker can peel off for adhesive mounting. RoboticsBD Operating Voltage (V): 12 DC 

Reference: RBD-1573

Five-Way Navigation Button Module 5D Joystick Independent Keyboard Switch Button Single Chip

1 review

Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm

Reference: RBD-1700

Brand: Waveshare

ST-LINK V2 Mini- STM Programmers & Debuggers

Mini ST-LINK/V2  Small single board Extreme low cost solution  In-circuit debugger/programmer  STM8 STM32.

Reference: RBD-2142

CH340C WIFI Module Adapter Download Debug for ESP8266 ESP-01/01S

2 reviews

Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.

Reference: RBD-2311

USB To Serial Cable TTL 4 Pin Rs 232 UART Converter Adapter Programming Module

1 review

USB 4 Pin TTL RS 232 UART Serial Converter Adapter Programming Module Cable. The PL-2303HX USB to TTL RS232 Serial converter is a low-cost USB to Serial Adapter.

Reference: RBD-0416

TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino

Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output

Reference: RBD-2315

Pogo Pin Probe Clip - 6 Pins with 2.54mm

1 review

Pin Pitch: 2.54mm Probe model: P75-E2 (pointed tip) Needle diameter: 1.3mm Needle sleeve model R75-3W Row pin number: 6Pin Row Number: Single row space between: 2.54mm

Reference: RBD-0312

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

1 review

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

Reference: RBD-2362

CH340G USB To TTL(Serial) Converter For Arduino Nano Raspberry Pi

Built-in USB to TTL Transfer chip. Designed to be used for USB to TTL electronic projects. TTL interface output, easy to connect to your MCU. Dual 3.3V and 5V Power output, work with 3.3v and 5 V target device. The mini-module is designed specifically for STC download and ARDUINO PRO supports all series of STC Supports WIN7/VISTA/MAC/LINUX(32 bit /64-bit...

Reference: RBD-2412

USB ASP AVR Programming Device for ATMEL Processors Arduino

1 review

Compatible Chips:ATMega Series Tiny Series Classic Series CAN Series PWM Series You can also use this to recover your Arduino Bootloader

Reference: RBD-0339

Brand: Waveshare

3.5inch Resistive Touch Display (B) for Raspberry Pi

3 reviews

3.5inch Resistive Touch Display (B) For Raspberry Pi 480×320 IPS Screen SPI Check out New Product 3.5inch HDMI Display-B

Reference: RBD-2413

FTDI Basic Breakout USBTTL 6PIN 5V Module Fio/Pro/RGB/Lilypad Programmer

Upgrade your Arduino Pro Mini, Lilypad and drone or RC aircraft with the ultimate ease and precision offered by our latest MWC MultiWii Lite/SE Flight Control Board Config Uploader. This innovative device comes packed with features designed to simplify the uploading and modification process. Save time and effort with the board's MINIUSB FTDI Basic USB...

Reference: RBD-0274

Brand: Waveshare

Raspberry Pi 5inch Resistive Touch HDMI LCD

1 review

5 inch Resistive Touch Screen LCD, HDMI interface, Designed for Raspberry Pi Installation Instruction: http://www.waveshare.com/wiki/5inch_HDMI_LCD Raspbian Image for 5 inch HDMI Diplay with Touch :  Raspbian 5 inch HDMI with Touch Download Link    

Reference: RBD-2416

WEMOS CH340G Breakout 5V 3.3V USB to Serial Module

5V (The max current depends on your USB port, usually 500mA) 3.3V (Using LDO, 300mA MAX) Use CH340G with stable performance. Driver: 1. CH340G USB to UART driver

Reference: RBD-2425

Shielded Blue USB Type-C Cable 30cm for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-1068

N20 12V 100 RPM Micro Metal DC Gear Motor

8 reviews

This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.

Reference: RBD-2427

USB Type-C Cable 1meter for Arduino

Now you can connect your Arduino boards, ESP or any other development platform with the Type-C USB Cable. Through a USB-C to USB-A connection, this data USB cable can easily connect your Arduino boards with your chosen programming device.

Reference: RBD-2463

Programmer Testing IC Test Clip Black SOIC8/SOP8 Flash Chip IC Test Clamp

The SOP8 test clip is made of high-quality plastic and copper metal, which is durable and can be reused.When using the SOP8 test clamp, do not force it down, open the clamp and clamp it in from the left and right sides of the chip.The same is true when disassembling, you can't pull it out directly, you must first separate the clip from left to right, and...

Reference: RBD-1248

Miniature Vibrating Motor

3 reviews

Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V

Reference: RBD-2086

Momentary Tactile Push Button Module DC 5V Switch

1 review

Operating Voltage: 5V Contact Resistance : 50mΩ max (initial) Electrically Life:100,000 cycles Environment temperature: -25°C to +105°C Operating Force: 180/230(±20gf) Seal temperature:250ºC-280ºC I/O pins: 3 pins

Reference: RBD-2655

ST-LINK/V2 CN In-Circuit Debugger/Programmer for STM8 and STM32

1 review

5V power supplied by a USB connector USB 2.0 full speed compatible interface USB standard A to mini B cable 1.65V to 5.5V application voltage supported on SWIM interface SWIM low speed and high-speed modes supported Made in China This product is a clone and might not support STM32Cube.

Reference: RBD-2714

ST-LINK V2.1 Emulator Debugger Programmer for STM32

The ST-LINK V2.1 emulator offers comprehensive support for all STM32 models, providing versatile functionality for development and debugging tasks. This product is a clone and might not support STM32Cube.

Reference: RBD-2243

LilyPad Button Board

1 review

Wearable e-textile technology.  Designed with large sew tabs Button Board

Reference: RBD-2746

QL2006 USB & RS232 PIC ICSP Programmer Emulator for Microchip MCU Programming

QL-2006 programmer is the high-speed programmer designed specially for development and production programming of PIC single chip microcomputer (SCM) by QLS Electronic Technology Co., Ltd. The product is featured with small volume, low power consumption, high reliability as well as easy and convenient operation.QL-2006 is applicable for almost all...

Reference: RBD-2244

LilyPad Slide Switch

Wearable e-textile technology.  Designed with large sew tabs Slide Switch

Reference: RBD-2290

PS2 Game Rocker Push Button Module for Arduino

X, Y axis output is two potentiometers, can read the twist angle through AD conversion. Press the rocker downward, you can move a touch switch, for digital output, has been pulled up. The original OMRON button has long life and good handle. It is suitable for two degrees of freedom steering gear pan tilt control or other remote control proportional...