Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0694
Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...
Reference: RBD-1565
MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm
Reference: RBD-2299
Package Included: 1 * TS101 Controller 1 * Anti-slip cap 1 * Original TS tip 1 * Power Adpater (AC100-240V to 24V 3A) 1 * USB-C silicone cable 1 * Mini Soldering stand 1 * 15g Solder wire 1 * User Manual Miniware TS101 Hardware Specifications Power USB C PD and QC 3.0 9-20 Volts (9-45W) DC 9-24 Volts (9-65W) Soldering Iron Tip TS-B2 (Conical 10mm)...
Reference: RBD-1244
Aluminum body with high torque metal gear servos 6 DOF structural design makes the robot arm move flexibly Up to 17Kg torque for joint servos Various control ways
Reference: RBD-1407
Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...
Reference: RBD-1748
80W Soldering Iron Soldering Iron Kit Set with Multimeter PU Bag
Reference: RBD-0948
Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V
Reference: RBD-1245
Soldering Iron Kit 21-in-1 with PU Bag by HANDSKIT Complete Soldering Kit: It includes the complete soldering tools for various uses, from home DIY, electrical repairs jobs and other soldering projects.
Reference: RBD-2123
STM32 chip for the main controller Easy Visual Operation Interface Support wireless handle control, smart phone APP and mouse control Provide graphical PC software and detailed tutorials The current Stock comes unassembled.
Reference: RBD-0375
AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)
Reference: RBD-1138
Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v
Reference: RBD-1937
Brand: Goot Original
Equivalent 45W-60W Power Ergonomic Design Economically priced general purpose soldering iron. Compact and lightweight design for easy handling. Available with Long life tip.
Reference: RBD-0552
Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD
Reference: RBD-2045
Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included
Reference: RBD-2256
Brand: Goot Original
Equivalent 40W Ergonomic Design Economically priced general purpose soldering iron. Compact and lightweight design for easy handling. Available with Long life tip.
Reference: RBD-1039
The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...
Reference: RBD-2194
Premium Quality Soldering Wire/Lead Low Melting Point Weight: 20-22 Gram 0.8mm Known as Lead or Solder Wire Melting Temperature 180°C Approx. (Tested by RoboticsBD LAB) We suggest this solder wire/lead paired with this solder to make your soldering work easier. Check GOOT Original KX-60R Soldering Iron 45W Check GOOT Original Soldering Iron TQ-77 here
Reference: RBD-2251
ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38
Reference: RBD-1037
Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.
Reference: RBD-1254
Size: 202X85X200mm Weight: 1150 gram MCU: STM32F105 Motor Drive: LV8731 motor driver chip Charging Direct
Reference: RBD-1938
Premium Quality Soldering Wire/Lead Low Melting Point Weight: 98-100 Gram with the spool. 0.8mm Known as Lead or Solder Wire Melting Temperature 180°C Approx. (Tested by RoboticsBD LAB) We suggest this solder wire/lead paired with this solder to make your soldering work easier. Check GOOT Original KX-60R Soldering Iron 45W Check GOOT Original Soldering...
Reference: RBD-0318
This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock. Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...
Reference: RBD-0833
Soldering Iron KOOCU V501 25W Constant Temperature Electric Soldering Iron Soldering Stand Soldering Lead Solder Resin Wire Cutter Sucker
Reference: RBD-1253
Program Software: Mixly + XR Scratch(base on Scratch2.0) Input: Edge sensor, Button, IR receiver module, Ultrasonic sensor, Tracking sensor Output: Buzzer, RGBLED, Two motor port,OLED CPU: Arduino UNO R3 Power: 2Pcs 3.7V DC Lithium battery Control: WiFi control/IR remote
Reference: RBD-0119
Brand: Goot Original
DESOLDERING SUCKER GS-100 Manual pump for solder removal Light, strong, and economical plunger pump Color: Ivory Length: 330mm when stored Weight: 89g Diameter: ø23mm
Reference: RBD-0345
802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD
Reference: RBD-1129
Brand: RoboticsBD
Complete Assembled Plug and Play Open Source Design Compatible With Arduino IDE DIY Kit
Reference: RBD-1252
Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes
Reference: RBD-1255
Integrated 0.96″ OLED Micro USB connection Compatible with Arduino Compatible with NodeMCU(Lua for ESP8266) Input Power 5V Compatible for Arduino Compatible with NodeMCU(Lua for ESP8266)
Reference: RBD-2165
Made in Japan The solder sucker has a large capacity cylinder and silicone tube at the tip for improved suction Nozzle is heat-resistant silicone tube that will not damage the object Flexible nozzle adheres to substrate for improved suction Clog prevention function automatically cleans the nozzle
Reference: RBD-1233
High-Quality Silicone Material Anti Static Material Magnetic slots to hold a small part Bright Colour for easy view of small components
Reference: RBD-1313
Indoor and Outdoor Tracked Robot Platform Designed for indoor or outdoor use and performs well on many different surfaces Its a very cool and completely functional model of the ever popular movie robot