How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-984
Heat Shrink Tubing 2:1, Eventronic Electrical Wire Cable Wrap Assortment Electric Insulation Heat Shrink Tube Kit (1 pcs) Please Choose Size Below
Reference: RBD-1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: RBD-245
Choose your desire Resistor value from below:
Reference: RBD-31
3 Types Available 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-94
Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.
Store Pickup Available!
Free Ship Over 5000 BDT
Quality Product
No Warranty
No Replacement
|
|
AT89C52
|
AT89C51
|
|
RAM
|
256 Bytes
|
128 Bytes
|
|
Flash
|
8 KB
|
4 KB
|
|
Number of Timers/Counters
|
3 (16-bit each)
|
2 (16-bit each)
|
|
Number of Interrupt Sources
|
8
|
6
|
|
Existing
|
Alternate
|
Function
|
|
P1.0
|
T2
|
Timer/counter 2 External Count input
|
|
P1.1
|
T2 EX
|
Timer/counter 2 Trigger input
|
Reference: RBD-1281
24C256 - Two Wire Serial EEPROM - 256KBits - 8PDIP Atmel Corporation
Reference: RBD-1606
The L297 Stepper Motor Controller IC generates four phase drive signals for two phase bipolar and four phase unipolar step motors in microcontroller controlled applications.
Reference: RBD-1289
IC 74LS164 8-bit Parallel-Out Serial Shift Register with Asynchronous Clear Package / Case: 14-DIP
Reference: RBD-1276
4N35 is an optocoupler IC in which an infrared emitter diode drives a phototransistor.
Reference: RBD-1297
The CD4027 is a CMOS based high voltage high speed Dual JK Flip-Flop package. The Flip-Flop could typically operate at a speed of 16MHz even at high voltages like 15V with a low noise margin of only 2.5V.
Reference: RBD-1098
The PCF8574 IO Expansion Board is used as remote 8-bit I/O expander for I2C-bus. Up to 8 PCF8574, IO Expansion Board can be connected to the I2C-bus, providing up to 64 I/O ports. The PCF8574 IO Expansion Board features I2C pinheader on one side and I2C connector on the opposite side. Hence, it's more flexible to connect the board to your development...
Reference: RBD-1354
Length: 8.5 inches (Medium) Material: Copper Plated.EachPin Spacing: 2.54mm.Color: Colorfulcompatible with 2.54mm mil spacing pin headers.It can be used for PCB project, pc motherboard, etc.Allow you to plug and unplug easily for prototyping.Package Contents: 1 x Jumper Wire You will get only one pcs.
Reference: RBD-753
5V Active buzzer to add some audio feedback to your Arduino project. With an active buzzer it's simple when you give it a single it will buzz, if you want more control of the audio you would like to produce take a look at our passive buzzers. SPECIFICATIONS Voltage: 5V Diameter: 12mm Pin Pitch: 7.6mm Height: 9 mm Current: <250mA
Reference: RBD-767
This passive buzzer needs an electrical signal (PWM) to make this buzzer buzz. This buzzer can use the Tone() command with an arduino.
Reference: RBD-837
18650 Li-ion Rechargeable Battery 3.7 Volt Rechargeable Lithium ION Re/Discharging Protection Circuit It's a clone battery so the ampere couldn't be guaranteed.
