Reference: RBD-1934

MQ-136 Hydrogen Sulfide Gas Sensor

Dual signal output (analog output and TTL level output) The TTL output effective signal is low. Analog output 0 ~ 5V voltage, the higher the concentration the higher the voltage. Good sensitivity to hydrogen sulfide, liquefied gas, natural gas, city gas, and smoke. with long service life and reliable stability fast response recovery characteristics

Reference: RBD-1066

Mini Metal Detector Module

Operating voltage: 5V DC. Detector distance: 1CM. Adjust the potentiometer, let the modules work normally. Small and easy to use module. It comes with a Buzzer for metal detection indication.The Mini Metal Detector Module arrives disassembled, requiring assembly using a soldering iron and soldering accessories. Moderate knowledge of soldering and...

Reference: RBD-2380

CJMCU-1080 HDC1080 High Precision Temperature And Humidity Sensor Module

The HDC1080 is a digital humidity sensor with integrated temperature sensor that provides excellent measurement accuracy at very low power. The HDC1080 operates over a wide supply range, and is a low cost, low power alternative to competitive solutions in a wide range of common applications. The humidity and temperature sensors are factory calibrated.

Reference: RBD-1248

Miniature Vibrating Motor

Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V

Reference: RBD-2082

Infrared IR Sensor Receiver Module for Arduino

Dimension: 2.5 x 1.5 x 1.5 cm. Receiving angle: 90 °. Working voltage: 2.7 ~ 5.5V. Frequency: 37.9KHz Receiving range: 18m. Weight: 4 gm.

Reference: RBD-2100

Flame Sensor Module

Comparator chip LM393 makes module readings stable. Operating voltage 3.3V-5V. Fast Response Time Sensitivity adjustable Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm. Detection range: up to 100 cm. Adjustable detection range. Detection angle about 60 degrees, it is sensitive to the flame spectrum.

Reference: RBD-1188

IR Infrared Transmitter - White (5mm)

5 mm Clear Transparent Round Small Lens (Emitting Angle: 30 degrees) Forward Voltage / Direct Current : DC 1.5 Volt 20 mA (Low Voltage Energy Saving) Infrared Ray 850nm (Luminous Invisible Light) for Night Vision CCTV Security Camera Polarity (1.5 V) : Anode (Longer Part) | Cathode (Shorter Part)

Reference: RBD-2096

Eye Blink Detection Digital Sensor with Goggles

Operating Voltage: 3-5.5V Supply Current: ≥ 20mA Optimal Sensing Distance: 3mm Working voltage of 5V, the output of the black line low, white line of high output Uses Infrared Light to Detect Anti-Interference Ability Sensors to adopt TCRT5000 High Sensitivity, Stable Performance Exquisite workmanship, with the indicator Has a fixed bolt hole for easy...

Reference: RBD-1243

AS608 Optical Fingerprint Sensor Fingerprint Module JM-101

Resolution: 500dpi Supply current: <60mA Supply voltage: 3.3V Fingerprint image entry time: <1.0 seconds Peak current: <60mA

Reference: RBD-1366

Infrared Temperature Gun Digital Thermometer

DT8380FC Infrared Thermometer Item no.: DT8380FC Temperature Range: -50~380°C/-58~716°F Measuring Accuracy: ±2% or 2C Distance Ratio: 12:1

Reference: RBD-1227

3D Scanner Laser Desktop- DIY Red

Object Scanning Device with USB 2.0 Interface / CMOS Sensor

Reference: RBD-1423

Brand: Raspberry Pi Official

Raspberry Pi High Quality Camera with 6mm Lens

Sony IMX477R stacked, back-illuminated sensor. Resolution: 12.3 megapixels. Compatible with Raspberry Pi 1/2/3/4 boards Output: RAW12/10/8, COMP8 Back focus: Adjustable (12.5 mm–22.4 mm) Lens standards: C-mount, CS-mount (C-CS adapter included) IR cut filter: Integrated Wide Field of View suitable for CCTV applications Suitable for macro photography...

Reference: RBD-0357

GY-ML8511 Ultraviolet Light UV Sensor Module

Operating voltage (VCC): 3 V to 5V Operating current: 120μA (typical) 190μA (max) Operating Temperature: -40°C ~ +85°C Photodiode sensitive to UV-A and UV-B Embedded operational amplifier Analog voltage output Low supply current (300uA type) and low standby current (0.1uA type) RoboticsBD

Reference: RBD-1719

Envitec OOM202 Medical Ventilator Oxygen Sensor

Envitec Honeywell OOM202 Medical Ventilator Oxygen Sensor Made in GermanyManufacture Date: 2023 December

Reference: RBD-2748

Reset / Enable Controller - KA75330 3.3V Voltage Detector

A voltage detector is handy for projects where you want to make sure your microcontroller doesn't run at a low voltage. For example, say you have a Feather Huzzah running on a lipoly battery every few minutes. Eventually, the battery runs down and goes below 3.3V, so the voltage to the ESP8266 core is too low, and could cause a lockup or corrupted data....

Reference: RBD-2378

4Pin Photodiode Sensor Module

4Pin Photodiode Sensor Module

Reference: RBD-2678

Surface Transducer - Large

Surface transducers give you the awesome power to turn almost any surface into a speaker. They're essentially just a speaker except instead of a cone, the coil is attached to a pad that conducts the vibration into whatever you press it against. Hook it up to an audio source and press it against the nearest table, wall or cardboard box. You can even put it...

Reference: RBD-2395

Mini HLK-LD2450 24G Smart Home Motion Target Tracking Radar Sensor Module Kit

mmWave human presence sensor. It uses motion target tracking and can detect up to 3 people. 

Reference: RBD-2125

QRE1113 Reflective Optical Sensor

Phototransistor output  No contact surface sensing  Miniature package

Reference: RBD-2998

Brand: DFRobot

Gravity: Analog Turbidity Sensor for Arduino

The Arduino turbidity sensor detects water quality by measuring the level of turbidity. It is able to detect suspended particles in water by measuring the light transmittance and scattering rate which changes with the amount of total suspended solids (TSS) in water. As the TTS increases, the liquid turbidity level increases. You may also check Liquid...

Reference: RBD-0411

HB100 Microwave Sensor 10.525GHz Doppler Radar Motion Detector Arduino

Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD

Reference: RBD-2729

SGP41 Air Quality Digital TVOC Detection Sensor

The SGP41 from Sensirion is an innovative VOC and NOx sensor engineered to serve as a digital smart switch and regulation unit in air treatment systems like air purifiers. Utilizing Sensirion's advanced Gas Index Algorithm, the sensor accurately processes two distinct signals, enabling automatic triggering of air treatment devices for the removal of...

Reference: RBD-2938

Brand: DFRobot

MODBUS-RTU RS485 Soil NPK Measure Sensor (IP68, 5-30V)

The Soil Sensor is a state-of-the-art device designed to provide rapid, accurate data on soil nitrogen, phosphorus, and potassium levels. This critical information allows for the optimization of soil fertility, creating the ideal environment for plant growth. With a wide voltage power supply range of 5-30V and data output via RS485 using the reliable...

Reference: RBD-0574

Honeywell HMC5983 Temperature Compensated Three-Axis Digital Compass

3-Axis Magnetoresistive Sensors and ASIC in a 3.0x3.0x0.9mm LCC Surface Mount Package Temperature Compensated Data Output and Temperature Output Automatic Offset Compensation. RoboticsBD

Reference: RBD-2099

Touch Sensor Switch Module

Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins

Reference: RBD-2964

0.8MPa G1/4" inch 5V Stainless Steel Pressure Transducer Sensor

Introducing the latest addition to RoboticsBD's product lineup, the 0.8MPa Stainless Steel Pressure Transducer Sensor. Crafted with high-quality stainless steel, this pressure transducer offers exceptional rigidity and durability, making it ideal for a variety of applications.

Reference: RBD-2730

SGP40 Air Quality Digital TVOC Detection Sensor

The SGP40 is a digital gas sensor designed for easy integration into air purifiers or demand-controlled ventilation systems. Sensirion’s CMOSens® technology offers a complete, easy-to-use sensor system on a single chip featuring a digital I2C interface and a temperature-controlled micro hotplate, providing a humiditycompensated VOC based indoor air...

Reference: RBD-2715

TEMT6000 Ambient Light Sensor Module

Visible light to analog voltage converter for measuring the intensity of visible light. Visible light sensitivity with peak at 570nm +/- 60 degree angle of sensitivity Fast reacting in uSec range. Analog voltage output proportional to the intensity of light falling on the detector 3.3 and 5V compatible

Reference: RBD-1199

Hall Effect Sensor A1302 49E

Low-noise output Fast power-on time Ratiometric rail-to-rail output 4.5 to 6.0 V operation Solid-state reliability Factory-programmed at end-of-line for optimumperformance Robust ESD performance 

Reference: RBD-2091

MY18E20 DS18B20 Compatible Temperature Sensor Module

Digital signal output 18B20 Temperature Sensor Chip (MY18E20 or DS18b20) Resolution adjustment ranges from 9-12 bytes. Send data via a pin Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.Compatible with DS18B20