Reference: RBD-0555

Current Sensor ACS712-30A

5 reviews

Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 30A Sensitivity: 100mV/A

Reference: RBD-0559

Voltage to Current Transmitter Signal Module

2 reviews

Power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA  0-5V to 4-20mA Linear Conversion

Reference: RBD-1347

TTP223 Capacitive Touch switch Digital Touch Sensor Module For Arduino

4 reviews

TTP223 Capacitive Touch switch Digital Touch Sensor Module for Arduino UNO DUE MEGA TTP223 capacitive touch single IC. Onboard level indicator. Working voltage: 2.0V to 5.5V.

Reference: RBD-0562

DC 3v-6v to 400kV 400000V Boost Step-up Power Module High-voltage Generator

3 reviews

Input Voltage: DC3.6V-6V Input Current: 2A-5A Output Voltage: DC 400KV (Please pay attention to safety when used) Input Line Length: about 100mm (red is positive) Output Line Length: about 160mm

Reference: RBD-0663

TTP223B Digital Touch Sensor Capacitive Touch

9 reviews

Power supply voltage(VCC): 2.0, 3, 5.5 V. Output high VOH: 0.8VCC V Output low VOL: 0.3VCC V Response time (touch mode) : 60 mS Response time (low power mode) : 220 mS Can replace the traditional touch of a button Four M2 screws positioning holes for easy installation RoboticsBD

Reference: RBD-0416

TTP229 8 Channel Digital Capacitive Switch Touch Sensor Module for Arduino

Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output

Reference: RBD-0564

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-0312

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

1 review

Arduino TTP229 16 Channel Digital Capacitive Switch Touch Sensor Module GM

Reference: RBD-1173

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000 100A

3 reviews

Input Current : 100A Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Meet UL94-V0 flame retardant properties

Reference: RBD-1175

Current Sensor ACS712-20A

3 reviews

Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 20A Sensitivity: 100mV/A

Reference: RBD-1677

52mm PP Liquid Water Level Sensor Horizontal Float Switch Down

Contact Rating: 10 W. Switching Voltage: 220 V. Switching Current: 0.5 A. Breakdown Voltage: 220 VDC. Carry Current: 1 A. Contact Resistance: 100 mΩ.

Reference: RBD-1174

Current Sensor ACS712-5A

8 reviews

Low-noise analog signal path. Device bandwidth is set via the new FILTER pin. 5 µs output rise time in response to step input current. Small footprint, low-profile SOIC8 package. 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.

Reference: RBD-1740

Vibration Sensor Module Vibration Switch Alarm Module for Arduino

1 review

Operating voltage: 3.3 to 5VDC Ball Rolling type of tilt sensor. This small module is easy to use. A fixed bolt hole for easy installation Wide voltage LM393 comparator

Reference: RBD-1177

4-20mA Signal Generator Current Loop Simulator Tester

This signal generator can use 4-20mA to generate voltage and control the current in the circuit. Accuracy up to 0.01; Liquid crystal display; Rotary encoder adjustment ; Two connection terminals are non polarity. Output range can be set; 4-20mA (device control) / -21mA (signal debugging) Display mode can be set, it is convenient for you to see the value...

Reference: RBD-1854

Resistive Film Pressure Sensor Module Pin Header Analog Signal 200mm

This module is compatible with various microcontroller control boards, such as arduino series microcontrollers. The module contains 2 kinds of interfaces. The module comes with a 20cm wire, which is long enough for your use. It has a short response time and quick response.

Reference: RBD-1344

Current to Voltage Transmitter Module

Supply voltage range: DC 7 V ~ 35 V Output voltage signal: 0 ~ 2.5 v, 3.3 v, 5 v, 10 v, 15 V. 4-20mA to 0-15V,0-5V,0-10V

Reference: RBD-2099

Touch Sensor Switch Module

Main chip: LM393 Working voltage: for DC 5V Single-channel signal output Low-level output signal used for human body touch sensor alarm Adjustable sensitivity Pin Connector to board: 4 Pins

Reference: RBD-1424

ZMCT103C 5A Range Single Phase AC Micro Current Transformer Sensor

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA. Rated input current: 5A Rated output current: 5mA Change: 1000: 1 The linear range: 0 ~ 10A (100 ohms) Linearity: 0.2%

Reference: RBD-2303

MAX30102 Heart Rate and Pulse Oximeter Sensor Module

3 reviews

LED peak wavelength: 660nm/880nm LED power supply voltage: 3.3~5V Detection signal type: light reflection signal (PPG) Output signal interface: I2C interface

Reference: RBD-1675

PZEM-004T V3.0 AC Digital Multifunction Meter Watt Power Volt Amp With Coil 100A

1 review

Model: PZEM-004T Operating Voltage: 80-260VAC Test Voltage: 80-260VAC Rated Current: 100A Rated power: 100A / 22000W Operating frequency: 45-65Hz Measurement accuracy: 1.0

Reference: RBD-2451

HW-827 Pulse Sensor 3.3-5V Heartbeat Heart Rate Monitor Sensor

HW-827 Pulse Sensor 3.3-5V Heartbeat Heart Rate Monitor Sensor Easy to use finger-tip heart rate detector module with built-in noise filter and signal amplification.

Reference: RBD-1835

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-050 50A

1 review

Input current (RMS): 50A. Work temperature: -25℃～+70℃. Storage temperature: -30℃～+90℃. Work voltage: 660V. Frequency range: 50Hz-1KHz.

Reference: RBD-2452

Pulse Heart Rate Sensor Kit For Arduino

This Pulse Sensor is a heart rate sensor designed for Arduino microcontrollers. Development professionals use. The Pulse Sensor Kit brings you all the experience you need, a complete package. The kit includes: A 24inch 3p DuPont line, A soft Velcro Finger Strap, A sensor size sensor ear clip, 4 Velcro dots, and 9 transparent protective dot Pulse Sensor is...

Reference: RBD-1836

Non-invasive AC current Sensor Split Core Current Transformer SCT-013-000 30A

2 reviews

Input Current : 0-30A Output Mode: 0-1V @ 30mA Frequency: 50HZ-150KHZ Opening Size: 13 x 13mm/ 0.5″ x 0.5″(L*W) Output Plug 3.5mm Dielectric Strength 6000V AC/1min Suitable for lighting equipment, AC motors, air compressors, monitoring, current measurement, and protection Meet UL94-V0 flame retardant properties

Reference: RBD-1972

Brand: DFRobot

Gravity: Analog AC Current Sensor (20A)

Brand Gravity Analog AC Current Sensor 20A AC Current Signal Conversion Module Open Type AC Transformer Probe Included Non-contact Measurement

Reference: RBD-2071

SS49E Linear Hall Effect Sensor Module

1 review

Type: Magnetic Sensor Module Mainly Compatible with: Ardunio

Reference: RBD-2072

Linear Magnetic Hall sensor

1 review

Operating Voltage: 3.3V-5V Features wide range voltage comparator LM393 Adjustable sensitivity Signal output indicator with the retaining bolt hole, convenient installation Output form digital switch output (0 and 1 high and low level) The output effective signal is low level When there is sound, outputs low level and the signal light

Reference: RBD-2073

A3144 Hall Effect Sensor Module

Digital Output Hall-effect sensor. Operating voltage: typically 5V. Output Current: 25mA. It can be used to detect both the poles of a magnet.

Reference: RBD-2120

HW670 5A Current Sensor

1 review

Onboard precision microcurrent transformer. Onboard sampling resistor. The module can measure AC currents less than 5A, the corresponding analog output 5A/5mA.

Reference: RBD-2224

Active Single Phase Voltage Transformer AC Voltage Sensor Module ZMPT101B

3 reviews

Voltage – 250V Easy PCB mounting Good consistency Widely acclaimed

Reference: RBD-2342

I2C SMBUS INA3221 Triple-Channel Shunt Current Power Supply Voltage Monitor Sensor Board

INA3221 3 Channel Shunt Current Voltage Monitor Sensor, high-side current and bus voltage monitor with an I2C- and SMBUS-compatible interface

Reference: RBD-2346

HW-671 WCS1800 Hall Current Sensor Over-current Protection Module Detection

HW-671 WCS1800 Hall Current Sensor Over-current Protection Module Detection