Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0015
2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...
Reference: RBD-0268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: RBD-0022
Affordable Price Operating Voltage: 5 V Sonar Sensing Range: 2-400 cm Max. Sensing Range: 450 cm Frequency: 40 kHz RoboticsBD
Reference: RBD-0028
Based on the W5100Based on the Wiznet W5100 allows an Arduino board to connect to the internet. Stackable Design, can directly be supported by for Arduino official Ethernet Library. Supports up to four simultaneous socket connections Can be used to store files for serving over the network. Can be accessed using the Mini SD TF library. IEEE802.3af...
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-1097
Frequency: 125Khz. Support μEM4001, 4100, or its compatible RFID, ID card. Read first 10 digits of the RFID/Proximity card. Support Windows95/98/2000/XP/7/8. Plug and Play Reliable working condition Powered directly from USB, no need external power supply
Reference: RBD-0023
Wide Working Voltage Range: DC 4.5V- 20V Current Drain: <60uA Detection Angle: <140° Detection Distance: 3 to 7m (can be adjusted) Blockade time: 2.5s (Default) Work temperature: -20-+80°C
Reference: RBD-0108
Works with standard (dual 5/3.3V) and 3.3V-only (for example, Pro Arduino) boards. Complies with USB Specification Revision 2.0 (Full-Speed 12Mbps Peripheral, Full-/Low-Speed 12Mbps/1.5Mbps Host) Supports HID devices, such as keyboards, mice, joysticks, etc. Compatible with Mass storage devices, such as USB sticks, memory card readers, external hard...
Reference: RBD-0346
The PN532 is a highly integrated transmission module for contactless communication at 13.56 MHz including microcontroller functionality based on an 80C51 core with 40 Kbytes of ROM and 1 Kbytes of RAM. The PN532 combines a modulation and demodulation concept completely integrated for different kinds of contactless communication methods and protocols at...
Reference: RBD-0815
Input Voltage: 100-240 V AC. Temp: 160~230 Deg settable. Filament: 1.75 mm PLA or ABS. This 3D Pen is designed for the freehand drawing of 3-Dimensional objects Adjustable output speed, temperature Create projects horizontally or vertically Every 3d pen will be checked and tested on our lab before shipping, so you will not received "intact" package. No...
Reference: RBD-0040
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-0159
Provides a user-friendly interface that allows users to go through the menu, make selections etc. It consists of a 1602 white character blue backlight LCD. The keypad consists of 6 keys select, up, right, down, left and reset. To save the digital IO pins, the keypad interface only uses one ADC channel. The key value is read out through a 5 stage voltage...
Reference: RBD-0313
Low power consumption, Low cost, and Compact size Read and write chip Fully integrated at 13.56MHz
Reference: RBD-1163
The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: RBD-0392
L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD
Reference: RBD-0820
"Take on any terrain with our burly off-road wheels." "Get the grip and stability you need with our deep-treaded tires." "Easy-to-mount and built to last - our off-road wheels won't let you down."
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0356
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0715
Voltage: 12V DC RPM:100RPM Diameter: 25mm Low Noise Shaft equips metal bushes for long life. Metal Gears for High performance It comes with High-Quality gears. High torque at very low Current Consumptions
Reference: RBD-0915
Maximum effective distance up to 150mm Less than 100ms decoding time Support external antenna Uart interface Support EM4100 compatible read-only or read/write tags Small outline design
Reference: RBD-0282
Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU
Reference: RBD-0750
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim
Reference: RBD-1099
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 1 to 5 cm (Depending on Antenna Geometry) Operating frequency: 125KHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anti-collision Printable Package Content: 1x Card
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-0306
Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android
Reference: 0828
Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking. Choose your...
Reference: RBD-1817
USB Plug and Play. RFID reader 0-8cm Reading Distance. Win8/7/XP/Android Supported. S50/S70 Card Supported. OTG Phone Connection. Built-in buzzer and LED for identification.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0716
Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 65 mm Width : 28 mm The material of Wheel: High-strength plastic The material of Tire: Rubber Color: Blue Rim Black Tire.
Reference: RBD-1950
Card reader MF522-MINI module uses the RC522 original chip to design the Supply Voltage 3.3V Works at a 13.56MHz frequency