Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-2196
USB Type: Type-A to Type-B Weight: 26 gm. Length: 50 cm Long cable for easy work Fully compatible with the PC. Molded strain relief and PVC over-molding to ensure a lifetime of error-free data transmissions.
Reference: RBD-0393
Dimensions: 40 x 27 x 15 (LxWxH) mm. RoboticsBD Weight: 10gm (without Hat). 2.54mm pin interface leads. Operating Voltage: 5V. Long service life and stable performance. Standard interface and electronic building blocks. Widely use in Arduino DIY projects. RoboticsBD
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0924
Driver Chip: MAX7219 Input Voltage: 3.7 to 5.3 V Input Current: 30 mA Display Dimensions: 42x24x12 (LxWxH) mm
Reference: RBD-1409
Voltage: 3.0 V – 5 V. Driver: APC circuit. Line length: about 135 mm. Transmit power: 58mW. Operating Current: 40mA. Operating Current: 40mA. Operating temperature: -36◦C ~ 65◦C. ** We've received reports from some customers that they were unable to make the product work. To avoid any inconvenience, we suggest that you refrain from making a purchase...
Reference: RBD-1573
Supports up/down/left/right/middle with extra set and reset button 2V-9V wide working voltage The number of IO: 7 Operating temperature: -40℃ to 85℃ Size: 4×2.5cm
Reference: RBD-1769
Input Voltage: 4.5V – 28V Output Voltage: 0.8V – 20V Output Voltage Adjustment: On-board potentiometer Output Current: 1.8A (typical), 3.0A (max). Ceramic Capacitor Stable Internal Soft-Start Internally Set Current Limit without a Current Sensing Resistor
Reference: RBD-1911
LM358 chip onboard. 100 gain of the circuit design. 10K onboard adjustable resistance, you can adjust the magnification. Onboard power indicator. The chip has led major pin can be directly input and output signals.
Reference: RBD-1916
IC Chip: MAX3232 Operating Voltage: 3.3-5.5V It can be used to program STC MCU, NXP MCU, Renesas MCU, STM32 MCU, N+-2EC MCU Pre-assembled compact size board Suitable for use with most microcontrollers Operates up to 250 kbit/s
Reference: RBD-2041
Model : KY-040. Type : Incremental Encoder. Cycles per revolution (CPR) : 20. Working voltage : 0 – 5V. Material : PCB + Brass. Mounting Nut Thread diameter: 6.6mm Weight : 10 gm.
Reference: RBD-2080
Clean, good waveform driving ability, more than 15mA. Working voltage 3.3V-5 Output format: digital switching output (0 and 1) A fixed bolt holes for easy installation
Reference: RBD-2084
Power supply: 3 – 5V Good sensitivity The output format: Digital switching output (0 and 1) The comparator output signal is clean, good waveform, driving ability, more than 15mA. A fixed bolt holes for easy installation. Using a wide voltage LM393 comparator.
Reference: RBD-2091
Digital signal output 18B20 Temperature Sensor Chip (MY18E20 or DS18b20) Resolution adjustment ranges from 9-12 bytes. Send data via a pin Temperature measurement ranges: -55°C to +125°C, be accurate to 0.5°C.Compatible with DS18B20
Reference: RBD-2094
The module can detect the surrounding environment of the humidity and temperature High reliability and excellent long-term stability The output from the digital output Humidity measuring range: 20%~90%RH(0~50 degree (temperature compensation). Temperature measuring range: 0~+50degree. Humidity measurement accuracy: ±5.0%RH. Temperature measurement...
Reference: RBD-2095
Detection distance: 2-40cm IO Interface: 4-wire interfaces (- / + / S / EN) Output signal: TTL level Adjustment: adjust multi-turn resistance Effective angle: 35 ° **Please be advised that the majority of our customers have left negative reviews for this product. We recommend that you do not make a purchase unless you are absolutely certain that you can...
Reference: RBD-2149
Capacity (Kg): 50. Output Sensitivity (mv/v): 1.0±0.1. Nonlinearity (%FS): 0.03. Repeatability (%FS): 0.03. Input Resistance (Ω): 1000. Insulation Resistance (MΩ): ≥5000.
Reference: RBD-2225
Output SPDT Relay. Header connector for connecting power and trigger voltage. LED indicates relay status. Screw terminal connector for easy relay output connection. Note: Relay brand may vary from actual product as our stock rotates.
Reference: RBD-2230
Main chip: NE555 Input Voltage: 5V-15V DC. Generate an adjustable pulse for MCU. Generate an adjustable pulse, to control circuitry associated.
Reference: RBD-2305
This is the 8 LED NeoPixel Ring, a small chainable 32mm outer diameter board equipped with 5050 WS2812 RGB LEDs. The WS2812s are each addressable as the driver chip is located inside the LED. Each NeoPixel Stick has ~18mA constant current drive so the color will be very consistent even if the voltage varies, and requires 5 V.
Reference: RBD-2314
8-bit WS2812B 5050 RGB LED Built-in Full Color Driver Development Board (Straight) is a great collection of WS2812B RGB Addressable LED Modules in a straight PCB. WS2812B is an intelligent LED that includes the photo diode and an addressable controller chip both are available and integrated into a single 5050 Components package. The major advantages of...
Reference: RBD-2411
Operating Voltage: 5V Pulse Number for One Circle: 20 Bi-directional Counting with No Limitation
Reference: RBD-2443
The Collision Switch Module is used to detect a collision with an object or to detect the limit of travel.
Reference: RBD-2453
Fully self contained panel meter with dual red and blue display.
Reference: RBD-2457
Regulates 4.5 – 40V input to a 1.25 – 37V output @ up to 1.5A
Reference: RBD-2461
XL7015 5V-80V DC-DC 0.8A Dc converter Step-down Module Wide Voltage Input LM2596
Reference: RBD-2564
This MOSFET module with optoisolation uses the LR7843 N-Channel logic compatible MOSFET with ultra low Rds(on) for moderate to higher current low-side switching applications of up to 15A continuous. N-Channel logic compatible MOSFET with optoisolation and ultra low 3.3mΩ Rds(on)
Reference: RBD-2565
Mosfet switch module on breakout board with screw terminals and pin headers. Useful for controlling high power loads (max 24V / 5A) using 3.3V / 5V logic circuits.
Reference: RBD-2566
With this High-Power MOSFET module you can easily use the double mosfet through the separate connections for power supply, switch pins and signal pins.The LED on the module indicates whether the MOSFET is switched on. This board is particularly useful for controlling a large LED strip (one color) or a motor (in one direction) by using. PWM.
Reference: RBD-2567
Interface between a CAN bus controller and the physical differential lines. Onboard TJA1050 CAN controller interface chip Chip commonly used pin has led, convenient connection to use Pin 5 v to the power supply PCB board size: 22 (mm) x11.5 (mm) Fully compatible with the ISO 11898 standard High speed (up to 1 Mbaud)Note : HW-021 on module working remains...
Reference: RBD-2671
IC: 25Q64FVSIG-1935 Capacity: 64M-bit / 8M-byte Clock frequency: <104MHz Working voltage: 2.7V ~ 3.6V Current: 4mA Dimensions (LxWxH): 15.5 x 14.5 x 3.7 mm
Reference: RBD-2725
Onboard LM386 Chip. 200 multiplier benefits circuit design. On-board speaker wiring Block. On-board 10K variable resistor, you can adjust the volume of the enlarged. Onboard power indicator.