Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0276
LOW QUIESCENT CURRENT: 460µA PRECISION VOLTAGE REFERENCE: 1.24V, 2.5V, 5V or 10V SLEEP MODE LOW OFFSET VOLTAGE: 250µV max LOW OFFSET DRIFT: 2µV/°C max
Reference: RBD-0347
9 Layer Acrylic stylish case with access to all Ports on Raspberry Pi 3 B/B+ Slot for Cooling Fan Easy to assemble with Nut-Bolts included Slots to route GPIO and CSI ribbon cable Cut-out for micro SC card at the bottom panel. RoboticsBD Note: Cooling fan is not included.
Reference: RBD-0954
Tell you the real capacity of your battery! LCD display show all info you want Micro-USB powered, charge everywhere at your will Charge all popular Li-ion batteries Unique efficient charge method (TC-CC-CV) with 0.5Ax2.
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0906
Slot for Cooling Fan Easy to assemble with Nut-Bolts included. RoboticsBD Cut-out for micro SC card at the bottom panel This simple case provides tough protection for your raspberry pi along with access to ports High Quality two-piece injection-molded ABS enclosure Click together design, no screws, standoffs or elastic bands required It is easy to use....
Reference: RBD-0955
Clearly see what’s going on with the batteries. Tachometer-style LCD display shows detailed charging status Powered by any 5V USB power Intelligently chooses charging currents from 0.1A to 1A Wide adaptability, adapts from 10440 to 32650, from Li-ion to Ni-MH Energy-saving LCD backlight, can be turned off at your will.
Reference: RBD-0383
Wide Supply Range: 2.0v To 5.5v Low Current Consumption Continuous Mode: Only 150µa Single-shot Auto Shut-down Programmable Data Rate: 8SPS to 860SPS It has Internal low-drift voltage reference
Reference: RBD-0836
Model: 14500 Type: Li-Ion Battery Mark Capacity: 850mah Nominal Voltage: 3.7v Color: Blue Weight: 17g Rechargeable Battery: Yes Note: It's a clone battery so the ampere couldn't be guaranteed.
Reference: RBD-0920
Acrylic Body. Easy to install. compatible with HC-SR04
Reference: RBD-0385
IC Name: MCP23017 Package/Case: DIP-28
Reference: RBD-0921
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0925
Hold 4 standard 18650 batteries. Wire Length: 15 cm. Output: 14.8 V. Dimension (Appro.) : 80 x 76 x 18 mm. Weight: 28 gm. High-quality plastic material
Reference: RBD-0411
Low current consumption (typical 30 mA) CW or pulse operation Flat profile Long detection range (20 m) Supply voltage: 4.75V to 5.25V X-Band Frequency: 10.525 GHz Minimum Power Output: 13 dBm EIRP. RoboticsBD
Reference: RBD-0837
Capacity (mAh): 960-1500 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life ***It's a clone battery so the ampere couldn't be guaranteed. RoboticsBD
Reference: RBD-1327
Package includes: 1 pcs x Acrylic Box ( without W1209 module ) DIY cover for W1209 Control Module Acrylic material looks transparent(may need to tear down the film). Easy for electronic enthusiasts to assemble.
Reference: RBD-0397
Support CAN V2.0B technical standard, communication rate 1Mb / S. Module 5V DC power supply, SPI interface protocol control 0 to 8 bytes long data field. 8MHZ crystal oscillator 120Ω terminal resistance Use High-speed CAN transceiver TJA1050 Impedance matching, guaranteed drive capability, long-distance data transmission, prevent signal radiation The...
Reference: RBD-0652
Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. RoboticsBD
Reference: RBD-1410
Compatible with Nvidia Jetson Nano Easy to assemble Slots to access all ports Cut-out for a fan at the top
Reference: RBD-0559
Power supply: DC 7-30 V Input Voltage: 0-10V Output current: 4-20mA 0-5V to 4-20mA Linear Conversion
Reference: RBD-0651
Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black.
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-0560
On-board MAX485 chip, A low power consumption for the RS-485 communication, slew-rate limited transceiver. A low power consumption for the RS-485 communication Onboard then 5.08 (mm) pitch 2P terminal to facilitate RS-485 communication wiring. Slew-rate limited transceiver All pins of the chip have been lead to can be controlled through the...
Reference: RBD-0732
Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch
Reference: RBD-1692
Color: Black lightweight Convenient to carry this battery box holder with wires Weight: About 9g Wire Length: Approx 14cm
Reference: RBD-0565
Compatible with MACH3, Linux CNC (EMC2) etc. parallel-control CNC software. USB power supply and peripherals power phase are separate to protect computer security. All the signals are to-isolate which can protect your computer security. 5-input interface to define the Limit, Emergence-Stop, Cutter alignment, etc. Wide input voltage range: 12-24V, and with...
Reference: RBD-0763
Cell Quantity: 2 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-1742
Holds 10 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 78X 60 X 28 Weight: 27.4 gm Material: Plastic Internal Connection: Series
Reference: RBD-0566
Fully compliant USB 2.0 standard, backward compatible with USB1.1 Support System: Windows XP, Vista, Windows 7, Linux, MacOS, and WinCE5.0 drive Baud Rate Range: 75bps – 115200bps, up to 6Mbps Supports Plug, Play and hot-swap ( USB side) Better than using CH341D chip or similar chip to support the laptop USB port. Communication distance up to 1.2KM
Reference: RBD-0764
Cell Quantity: 3 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC
Reference: RBD-1743
Holds 6 x AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 58X 48 X 28 Weight: 15.6 gm Material: Plastic Internal Connection: Series
Reference: RBD-0695
Integration Lowers System Cost, Simplifies Design Efforts, and Reduces Design Cycle Time High Accuracy Facilitates Meeting Error Budgets 15-Bit ADC Resolution; Nominal Temperature Resolution 0.03125NC (Varies Due to RTD Nonlinearity) Total Accuracy Over All Operating Conditions:
Reference: RBD-0765
Holds 4 AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 62 x 58 x 15 Weight: 15 gm Material: Plastic Internal Connection: Series