Reference: RBD-0015

Motor Shield L293D

97 reviews

2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...

Reference: RBD-0166

XBee 1mW Trace Antenna - Series 1 (802.15.4)

Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...

Reference: RBD-0268

Brand: RoboticsBD

3D Printed Robotics claw with servo motor

Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R

Reference: RBD-1093

LOGO! TD Text Display 6ED1055-4MH08-0BA0

LOGO! TD Text Display, 6-line, 3 background colors, 2 Ethernet ports, installation accessories for LOGO! 8

Reference: RBD-0267

Big Easy Driver - Stepper Motor Driver

1 review

Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...

Reference: RBD-0286

Arduino Uno R3 Bumper

4 reviews

3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included

Reference: RBD-0369

Brand: SparkFun Electronics

XBee Pro 63mW RPSMA - Series 2B (ZigBee Mesh)

Supports binding and multicasting for home automation Mesh-network topology 2.4 GHz for worldwide deployment Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board Firmware upgrades via UART, SPI or over the air TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC DATA RATE: 250kbps Max RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile...

Reference: RBD-2156

4×4 Matrix 16 Keyboard Keypad

2 reviews

Easy communication with any microcontroller. Tactile type switches. Over 1,000,000 operations per key. Contact rated for 12V dc @ 20mA. Over 1,000,000 operations per key.

Reference: RBD-0189

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Reference: RBD-0289

16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685

14 reviews

Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED

Reference: RBD-0815

3D Pen 2nd Generation LED Display Screen with (6 Color Filament)

6 reviews

Input Voltage: 100-240 V AC. Temp: 160~230 Deg settable. Filament: 1.75 mm PLA or ABS. This 3D Pen is designed for the freehand drawing of 3-Dimensional objects Adjustable output speed, temperature Create projects horizontally or vertically Every 3d pen will be checked and tested on our lab before shipping, so you will not received "intact" package. No...

Reference: RBD-0306

Torobot 32 Channel USB UART Servo Motor Controller

1 review

Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android

Reference: RBD-0400

NRF24L01+PA+LNA 2.4GHz SMA Antenna Wireless Transceiver communication module 1pcs

16 reviews

Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....

Reference: RBD-1163

Robotics Arm EEZYbotARM MK1

The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.

Reference: RBD-0196

Brand: DFRobot

APC220 Radio Communication Module 1KM Line of sight (LOS)

1 review

The APC220 radio module offers a cost-effective solution for wireless data communications, featuring an embedded high-speed microprocessor and high-performance IC. With its transparent UART/TTL interface, it eliminates the need for packetizing and data encoding, making it a popular choice among customers seeking better range performance at a low cost.

Reference: RBD-0376

L298N H-Bridge Dual Motor Driver, Stepper Motor Driver

139 reviews

Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes

Reference: RBD-1683

PLA Filament for 3D Pen

3 reviews

Compatible with 3D pen 15gram-17gram 1.75mm Random Color

Reference: RBD-0237

APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW

Description: This Telemetry radio set allows you to link to  a flight controller such as the APM or Multiwii  AIO via a USB equipped device such as a  computer, laptop or tablet supporting a USB  connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)

Reference: RBD-0356

Abs Material 2 Axis Pan Tilt Camera Mount With MG90

1 review

PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0389

PL2303 USB to TTL Serial Converter

14 reviews

Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...

Reference: RBD-0392

Ardumoto Shield L298P Motor Driver

L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD

Reference: RBD-1364

Holder for 10 mm LED light strip

10 mm LED light strips. Attached with a nail or a screw.

Reference: RBD-0434

DRV8825 Stepper Motor Driver Module

5 reviews

Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD

Reference: RBD-0658

FTDI USB to TTL Serial Converter Adapter FT232RL

22 reviews

Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...

Reference: RBD-0251

Jumper Wire housing 3 Pin

1 review

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0435

A4988 StepStick Stepper Motor Driver Module

3 reviews

Supply Voltage : 8-35 VDC. Current : 1.0A  (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.

Reference: RBD-0439

Arduino Android IOS HM-10 BLE Bluetooth 4.0 CC2540 CC2541 Serial Wireless Module

12 reviews

Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....

Reference: RBD-0040

Arduino Bluetooth Module HC-06

40 reviews

Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.

Reference: RBD-0260

Jumper Wire housing 5 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0557

30A Mini VNH2SP30 Stepper Motor Driver Monster Moto Module For Arduino

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0262

Jumper Wire housing 6 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.