Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0234
Brand: SparkFun Electronics
Description: This is a 7" LVDS LCD Cape for the pcDuino V3 with a 1024x600 screen resolution and capacitive touch from LinkSprite. This massive screen is a great addition for the pcDuino V3 that compliments its extreme versatility as a mini PC development platform.
Reference: RBD-0268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: RBD-0390
Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).
Reference: RBD-0218
High Torque Gear Motor 12V, 50 RPM Volt: DC 12V RPM: 50 Torque 13KG/CM
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-0412
Microchip's PICkit3 In-Circuit Debugger/Programmer uses in-circuit debugging logic incorporated into each chip with Flash memory to provide a low-cost hardware debugger and programmer. The MPLAB PICkit3 allows debugging and programming of PIC® and dsPIC® Flash microcontrollers at a most affordable price.
Reference: RBD-2440
Brand: Raspberry Pi Official
১ টি রাস্পবেরি পাই 5 (Made in UK) RAM: 8GB একসাথে দুটি HDMI মনিটর লাগানো যায়। ১ টি রাস্পবেরি পাই ৫ কেসিং ১ টি রাস্পবেরি পাই ৫ অ্যাক্টিভ কুলার রাস্পবেরি পাই এর ইউএসবি -সি পাওয়ার এডাপটার ২৭ওয়াট ট্রান্সসেন্ড অথবা স্যানডিস্ক ব্রান্ডের জেনুইন ৬৪ জিবি অথবা ১২৮ জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ। বিল্ট ইন Wi-Fi & Bluetooth গিগাবিট...
Reference: RBD-0573
Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm
Reference: RBD-0815
Input Voltage: 100-240 V AC. Temp: 160~230 Deg settable. Filament: 1.75 mm PLA or ABS. This 3D Pen is designed for the freehand drawing of 3-Dimensional objects Adjustable output speed, temperature Create projects horizontally or vertically Every 3d pen will be checked and tested on our lab before shipping, so you will not received "intact" package. No...
Reference: RBD-1101
Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB
Reference: RBD-2441
Brand: Raspberry Pi Official
১ টি রাস্পবেরি পাই 5 (Made in UK) RAM: 4GB একসাথে দুটি HDMI মনিটর লাগানো যায়। ১ টি রাস্পবেরি পাই ৫ কেসিং ১ টি রাস্পবেরি পাই ৫ অ্যাক্টিভ কুলার রাস্পবেরি পাই এর ইউএসবি -সি পাওয়ার এডাপটার ২৭ওয়াট ট্রান্সসেন্ড অথবা স্যানডিস্ক ব্রান্ডের জেনুইন ৬৪ জিবি অথবা ১২৮ জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ। বিল্ট ইন Wi-Fi & Bluetooth গিগাবিট...
Reference: RBD-0309
4 poles 12 slot Hi-torque motor design CNC machined 6061 T6 windings maximizes efficiency High RPM ABEC5 oversize bearings Universal fit, fit all 1/10 brushless cars-multi-mounting system for M3 screws Precision balanced rotor, smoothness for best reliability and maximum RPM
Reference: RBD-1102
PCB installed inside of aluminum alloy U disk shell, portable, safe and reliable! Interface definition directly marked on the shell, clear, convenient and practical! 5V, 3.3V offers at the same time, allowing you to program your target board with both 5V and 3.3V Shell characters using laser engraving, never fade off! Permanent clarity! 500MA internal...
Reference: RBD-1163
The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.
Reference: RBD-1593
১ টি রাস্পবেরি পাই 4 (Made in UK) RAM: 1GB, 2GB, 4GB, 8GB (পছন্দ করে নিতে পারবেন) একসাথে দুটি HDMI মনিটর লাগানো যায়। ১ টি Argon One V2 Case কেস। রাস্পবেরি পাই এর ইউএসবি -সি পাওয়ার এডাপটার সুইচ সহ। ট্রান্সসেন্ড অথবা স্যানডিস্ক ব্রান্ডের জেনুইন ১৬ জিবি অথবা ৩২ জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ। বিল্ট ইন Wi-Fi & Bluetooth গিগাবিট...
Reference: RBD-0217
Model: MG90S Weight: 13 gm Operating voltage: 4.8V~ 6.6V Servo Plug: JR Stall torque @4.8V : 1.8kg-cm Stall torque @6.6V : 2.2kg-cm Note: The component, colour & shape of the motor may vary depending on our stock rotation.
Reference: RBD-1103
Stably support SignalTap II embedded logic analyzer function, no mistake while crawling data. Fully support all Altera products such as CPLD: MAX3000, MAX7000, MAX9000 and MAXII. FPGA: Stratix, StratixII, StratxIII, Cyclone, CycloneII, CycloneIII, ACEX1K, APEX20K and FLEX10K etc. Active serial configuration device: EPCS1, EPCS4, EPCS16, EPCS64 etc....
Reference: 1141
Brand: Raspberry Pi Official
১ টি রাস্পবেরি পাই 4 (Made in UK) RAM: 1GB, 2GB, 4GB, 8GB (পছন্দ করে নিতে পারবেন) একসাথে দুটি HDMI মনিটর লাগানো যায়। ১ টি কুলিং অ্যালুমিনিয়াম মেটাল ফ্যান কেস। রাস্পবেরি পাই এর হিট সিংক। রাস্পবেরি পাই এর ইউএসবি -সি পাওয়ার এডাপটার সুইচ সহ। ট্রান্সসেন্ড অথবা স্যানডিস্ক ব্রান্ডের জেনুইন ১৬ জিবি অথবা ৩২ জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ।...
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-0020
Model: SG90 Weight: 9 gm Operating voltage: 3.0V~ 7.2V Servo Plug: JR Stall torque @4.8V : 1.2kg-cm Stall torque @6.6V : 1.6kg-cm Note: Product images/ Components brand may vary from actual product as our stock rotates.
Reference: RBD-0356
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-1104
Isp interface: 6 PIN Isp interface: 10 PIN Power supply options: USB power Power supply options: external power supply (remove jumper cap)
Reference: RBD-1850
Brand: Raspberry Pi Official
১ টি রাস্পবেরি পাই 400 (Made in UK) RAM: 4GB (Fixed) একসাথে দুটি HDMI মনিটর লাগানো যায়। রাস্পবেরি পাই এর ইউএসবি -সি পাওয়ার এডাপটার সুইচ সহ। স্যানডিস্ক ব্রান্ডের জেনুইন ৩২ জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ। বিল্ট ইন Wi-Fi & Bluetooth গিগাবিট ইথারনেট পোর্ট। ২ টি USB 3.0 & ১ টি USB 2.0
Reference: RBD-0034
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm
Reference: RBD-1106
XGecu Super Mini Pro T48 Universal Programmer
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-1519
Brand: Raspberry Pi Official
Quad-Core 64-bit Broadcom 2711, Cortex A72 Processor WLAN 802.11 b/g/n/ac (2,4 + 5,0 GHz) LAN RJ45 10/100/1000 Mbit (Gigabit LAN over USB 3.0) Operating Power 5V@3A via USB Type-C port. Keyboard Layout: US Dual-Display Micro HDMI Ports which supports H 265 Decode for 4K Video @60p Built-in Raspberry Pi Official Keyboard
Reference: RBD-0295
Model: MG995 Weight: 55 gm Operating voltage: 4.8V~ 7.2V Servo Plug: JR Stall torque @4.8V : 9.4kg-cm Stall torque @6.6V : 11kg-cm Continuous rotation servos are like regular hobby RC servos but modified to offer speed control instead of position control. They're essentially compact, affordable motors with integrated motor drivers. Add a wheel, and...
Reference: RBD-1212
Single crystal 12M Tablet 340 USB port to serial port communication. USB1.1/2.0 compliant solution. Built-in 128 byte TX/512 byte RX buffer. Supports auto-Handshake Protocol. Support Win95/98/98se/ME/2000/XP/win7 32bit 64bit/Vista/supports full speed USB data transfer protocol. Design of electromagnetic interference. Data Exchange application. CH340 USB...
Reference: RBD-2439
Brand: Raspberry Pi Official
Model: Raspberry Pi 5 Model 8GB Ram: LPDDR4X-4267 8GB SDRAM PCIe 2.0 x1 interface for fast peripherals 5V/5A DC power (PD enabled) Real-Time Clock (RTC), powered by an external battery On-board power button!! Stock is available with Complete Set. Please purchase Raspberry Pi 5 Complete Set.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0297
Weight: 55g Dimension: 40.7×19.7×42.9mm Stall torque: 9.4kg/cm (4.8v); 11kg/cm (6.0v) Operating speed: 0.19sec/60degree (4.8v); 0.15sec/60degree (6.0v) Operating voltage: 4.8 ~ 6.6V Gear Type: Metal gear Dead band width: 1us Wire length: 32cm