Reference: RBD-0390

12V 37GB550 Gear Motor High Torque 60 RPM

3 reviews

Features of 60 RPM High Torque 12 Volt DC Gear Motor: 60RPM 12V DC motors with Metal Gearbox and Metal Gears. 20000 RPM base motor. 6mm Dia shaft with M3 thread hole. Length 63 mm without shaft. Shaft length 30mm. 275gm weight. 20 kg cm torque. No-load current = 0.15 mA, Load current = upto 4 A(Max).

Reference: RBD-0750

85mm Antiskid Shockproof Wheels, Smart Car Robot Tires with 37GB Motor

Tire with sponge liner for more strength With upgraded tire tread for greater friction New design wheel for better combination with the motor Diameter: 85 mm Width : 38 mm The material of Wheel: High-strength plastic The material of Tyre: Rubber Color: Black Tyre + Blue Rim

Reference: RBD-0818

LDX-218 Servo Motor

2 reviews

17kg large torque. 15 kg·cm (208 oz·in) @6V 17 kg·cm (236 oz·in) @7.4V Full metal gear 180 degree rotation Using high-precision potentiometer with new design Convenient plug-in wire

Reference: RBD-0819

Hiwonder LDX-227 Servo

3 reviews

17kg large torque. 15 kg·cm (208 oz·in) @6V 17 kg·cm (236 oz·in) @7.4V Full metal gear 270 degree rotation Using high-precision potentiometer with new design Convenient plug-in wire

Reference: RBD-0936

1100 GPH 12V Submersible Marine Boat Bilge Water Pump

7 reviews

High-Quality Pump Operating Voltage: 24VDC Flow Rate: 1100GPH Outlet Diameter 19mm

Reference: RBD-0127

Obstacle Avoiding Robot Kit

Obstacle Avoiding Robot Kit

Reference: RBD-1250

Heavy Duty High Torque Gear Motor

2 reviews

DC 12V 100 RPM Torque 10 kg-cm 37GB-550 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-0268

Brand: RoboticsBD

3D Printed Robotics claw with servo motor

Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R

Reference: RBD-1357

12V 37GB550 Gear Motor High Torque 300 RPM

1 review

DC 12V 300 RPM Torque 4 kg-cm Consumes less current  Higher durability 

Reference: RBD-1390

Nema 17 Stepper Motor 17HS4401S

3 reviews

Nema17 Bipolar. Number of Phases: 2. Step Angle: 1.8°. Phase Voltage: 2.6Vdc. Phase Current: 1.7A. Resistance: 1.5Ω ±10%. Inductance: 2.8mH ±20% (1KHz). Number of Wire: 4 (100cm Length). Holding Torque: 43N.cm. Shaft Diameter: Ø5mm. Motor Length: 40mm. Mass: 270g.

Reference: RBD-0166

XBee 1mW Trace Antenna - Series 1 (802.15.4)

Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...

Reference: RBD-1682

12V 37GB550 Gear Motor High Torque 100 RPM

2 reviews

DC 12V 100 RPM Torque 12 kg-cm 37GB-550 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-1868

DC 12V 60W High Pressure Micro Diaphragm Water Pump Automatic Switch 5L/min Range 8m Water Pump

1 review

Watering configuration: much the same, additional sprinklers and timers are required 12V DC reflux diaphragm pump 550, the price is the price of a pump, without other accessories Maximum pressure: 0.8MP. Voltage: 12V, current: at least 2A, measured 1A is not able to bring Suction: 3 meters or so, preferably 2 meters (no problem if the vertical height is...

Reference: RBD-0226

Brand: SparkFun Electronics

Camera Module - pcDuino V3 (2MP)

Camera Module - pcDuino V3 (2MP)

Reference: RBD-1960

Mini Peristaltic Pump Head with Tube

Small size, light weight. Embedded in the work front panel Mounted on the carriage.

Reference: RBD-0235

Brand: SparkFun Electronics

Graphic LCD 128x64 STN LED Backlight

Description: This is a framed graphical LCD 64x128 with  LED backlight. This unit is a very clear STN type LCD with  a simple command interface. This new module includes the negative voltage circuitry on board!

Reference: RBD-0258

Brand: SparkFun Electronics

SparkFun Micro OLED Breakout

SparkFun Micro OLED Breakout

Reference: RBD-0267

Big Easy Driver - Stepper Motor Driver

1 review

Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...

Reference: RBD-0288

GY-801 - Multi Sensor Board

1 review

Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v

Reference: RBD-2250

JGY-370 DC 12V 160RPM Self-locking Reduction Worm Gear Motor

JGY-370 DC 12V 160RPM Self-locking Reduction Worm Gear Motor

Reference: RBD-2277

12V 37GB550 Gear Motor High Torque 400 RPM

Reliable Versatile Efficient

Reference: RBD-2067

7-70V 30A PWM DC Motor Speed Controller Switch with 30 Amp Fuse

7-70V 30A PWM DC Motor Speed Controller Switch Wide voltage input range: 7-70V Maximum output current: 30A Speed control knob with switch function Adjustable potentiometer with flexible cable (15cm length) Includes a 30A fuse for motor interface protection Input power must be 1.5 times greater than the motor's rated power

Reference: RBD-0334

9 Degrees of Freedom Breakout- MPU9150

1 review

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Reference: RBD-2524

12V 37GB550 Gear Motor High Torque 200 RPM

DC 12V 200 RPM Torque 12 kg-cm 37GB-550 Gear Reducer Motor Consumes less current  Higher durability 

Reference: RBD-2803

NEMA17 42BYGH40 2-Phase 4-Wire Stepper Motor for 3D Printers

This is NEMA17 stepper motor commonly used in 3D printers, CNC machines, and linear gantry systems.

Reference: RBD-0382

GY-87 10DOF MPU6050 HMC5883L BMP180 Sensor Module

1 review

3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD

Reference: RBD-0394

Slip Ring - 6 Wire (1.5A) max 240V

They are very useful for connecting components to wires. It is insulation covered clips connected to the wire from both ends. RoboticsBD

Reference: RBD-0436

3D Printer Controller for RAMPS 1.4 REPRAP MENDEL PRUSA

1 review

Supply Voltage: 12V Standard interfaces (as that of the extruder) Reserved GCI like I2C and RS232 3 MOSFET’s are applied to the heater/ fan and thermistor circuit. Another 5A added to protect the component parts. An 11A fuse is added to the hotbed. Support 5 stepper drive board

Reference: RBD-0692

4-20MA -50~150℃ RTD PT1000 SBW Temperature Sensor Transmitter Module

Accuracy: +/- 0.2F.S Temperature coefficient: Less than 150ppm/K F.S. Working temperature: 0-100℃ Working humidity: Less than 98% RH

Reference: RBD-0419

SparkFun Particle Sensor Breakout - MAX30105

Features: Built-in Red, IR, and Green LEDs 5V operation (3.3V is allowed, but green LED is not guaranteed to operate) Applications include presence detection, distance sensing (18" max), pulse oximetry, blood oxygen saturation level (SpO2), smoke and particle detection Documents: Schematic Eagle Files Hookup Guide Datasheet (MAX30105) MAX3010x Sensor...

Reference: RBD-0417

Force Sensor Resistor Square 38.1mm

3 reviews

Easily customizable to a wide range of sizes Cost-effective Ultra-thin; 0.45 mm Robust; up to 10 million actuations Simple and easy to Integrate. RoboticsBD

Reference: RBD-1241

Mecanum Wheel 80mm for Advanced Robotics (Left + Right) Pair

4 reviews

Color: Black Weight: 120g (each) Outer wheel diameter: 80mm Thickness: 37mm 1 pcs Left and 1 pcs Right Wheel No Connecting Hubs