Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-1101
Supply voltage:5 V Microcontroller:ATtiny44 Connection port:micro USB
Reference: RBD-0149
Output Channel: 1 Power Supply: 3.3/5V Built in a potentiometer for sensitivity control. Onboard signal output indication, output effective signal is high, at the same time the indicator light up, the output signal can directly connect to microcontroller IO. Detection angle about 60 degrees, the flame spectrum especially sensitive. The flame of the most...
Reference: RBD-0272
Brand: Waveshare
Voltage level: 1.8V-6V Dimension: 38mm x 31.6mm Conversion level range: 1.8 V-6 V Instructions for use: (3.3 V, 5 V to each other) 4 pairs of power supply interfaces, supports more situation Use tantalum capacitors for power filter, provides more stability VCCB 5V power supply (can be an external 5V power supply)
Reference: RBD-0291
Main chip: LM393, Electret condenser microphone Working voltage: DC 3.3-5V Induction distance is 0.5M Signal output Indication Single channel signal output The output effective signal is low level.
Reference: RBD-0132
The TCRT5000 and TCRT5000L are reflective sensors which include an infrared emitter and phototransistor in a leaded package which blocks visible light. The package includes two mounting clips. TCRT5000L is the long lead version. Model TCRT5000 Color Black + blue Detecting range: 0.591″ (15mm); Detecting method: Reflective; Collector-Emitter: Voltage:...
Reference: RBD-0307
Operating Voltage(V): 3- 5 Operating Current(mA): 2 Communication protocol: I2C Power saving mode Automotive grad Small size, low cost. RoboticsBD
Reference: RBD-0147
Adjustable Sensitivity, External GND. Detect Ambient Humidity. Provided with Fixed Bolt Hole, Convenient to Install. Power Indicator Light & Digital Output Indication Lamp. Using LM393 Chip for Stable Work. DO Small Digital Outputs Interface (0 & 1).
Reference: RBD-0337
Brand: Waveshare
Detection depth: 48mm Power: 2.0V ~ 5.0V Dimension: 19.0mm * 63.0mm Mounting holes size: 2.0mm
Reference: RBD-1700
Brand: Waveshare
Mini ST-LINK/V2 Small single board Extreme low cost solution In-circuit debugger/programmer STM8 STM32.
Reference: RBD-0151
Operating voltage 3.3V-12V A fixed bolt hole for easy installation Wide voltage LM393 comparator Maximum output current: 15mA Can work on low voltages
Reference: RBD-0152
Using SW-420 normally closed type vibration sensor Comparator output, clean signal, good waveform, strong driving ability, >15mA Operating voltage 3.3V ~ 5V Output format: digital switching output (0 and 1) Using a wide voltage LM393 comparator With bolt holes for easy installation
Reference: RBD-2142
Operating Voltage: 5VDC USB to Serial Converter: CH340C Compatible With:ESP8266 ESP-01/01S Comes With Onboard Reset Switch Has Female Headers for Connecting the Wifi Module.
Reference: RBD-0156
Operating Voltage: 3V-5V High-resolution conversion of light intensity to frequency. Chip pins all has drawn for standard 100. Put the needle (2.54 mm). Mil-convenient for bitmap board. Programmable color and full-scale output frequency. Communicate directly with a microcontroller. Low-profile surface mount package.
Reference: RBD-0222
Sound pressure level: 85DB 10cm The input voltage: 30vp-p max Ultra-thin and lightweight Low power consumption for voltage type Operating Temperature: -20~70 Storage Temperature: -30-80 Clear sound
Reference: RBD-0150
Output Power: 5mW Working Voltage: 3-3.3V DC Working temperature: -10 ℃~+40 ℃ Housing material: Copper Working life: more than 2000 hours Spot mode: Dot Facula (continuous output) Laser wavelength: 650nm red-colored. Operating current: <40mA Power lead length: 120mm. 5V could damage the laser
Reference: RBD-0241
Calibrated directly in Degree Celsius (Centigrade) Linear at 10.0 mV/°C scale factor 0.5°C accuracy guarantee-able (at a25°C) Suitable for remote applications Low cost due to wafer-level trimming Operates from 4 to 30 volts Less than 60 mA current drain Low self-heating, 0.08°C in still air Non-linearity only 0.25°C typical LM35 (working) tested by...
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0288
Three selectable full scales (250/500/2000dps) Factor in all g-ranges, up to 13-bit resolution at ±16 g 12-Bit ADC Coupled with Low Noise ARM Sensors Achieves 5 milli-gauss Resolution in ±8 Gauss Fields Pressure range:300 to1100hPa (+9000m to -500m above sea level) I2C interfaces Power supply: 3-5v
Reference: RBD-0433
5V power supply. Serial I2C control of LCD display using PCF8574. RoboticsBD Backlight can be enabled or disabled via a jumper on the board. Contrast control via a potentiometer. Can have 8 modules on a single I2C bus (change address via solder jumpers)address, allowing.
Reference: RBD-0344
Output Sensitivity: 1.0 ± 0.1 mV / V. Two selectable differential input channels. On-chip active low noise PGA with the selectable gain of 32, 64 and 128. On-chip oscillator requiring no external component with optional external crystal. On-chip power-on-reset. Measurement Resolution: 24 bit. RoboticsBD
Reference: RBD-0352
Detect shocks with the spring and send a signal to Controller Board Operating voltage: 3.3V-5V Digital output Bolt holes for easy installation. RoboticsBD
Reference: RBD-0354
Approximates Human eye Response Extremely wide dynamic range 1 to 600,000,000 Counts Lux Range: 188u Lux sensitivity, up to 88,000 Lux input measurements Voltage range: 3.3-5V into the onboard regulator This board/chip uses I2C 7-bit addresses 0x29 and 0x28. RoboticsBD
Reference: RBD-0368
Thickness: 0.4mm Trigger Force: 20g, triggered (default resistance<200kΩ) Pressure Measuring Range: 20g~6kg Static Pressure & Dynamic Pressure Measurement (within the frequency of 10Hz) Initial Resistance: >10MΩ Activation Time: <0.01S Operating Temperature: -40°C~+85°C Lifespan: >1million times Hysteresis: +10%,(RF+ -RF-)/FR+,1000g...
Reference: RBD-0382
3-axis Gyro+Acceleration+Magnetic Fiel Air Pressure Module Power supply: 3-5V Build in ultra low noise linear LDO voltage regulator Built-in onboard filters, which reduce noise from motor and other high current electronics You can easily select two I2C address for MPU6050 by soldered jumper. RoboticsBD
Reference: RBD-0832
Power supply: 4.5V – 5.5V, 3.3V voltage regulator circuit board Positioning holes: 4 M2 screws positioning hole diameter of 2.2mm Control Interface: GND, VCC, MISO, MOSI, SCK, CS Size: 45 x 28mm Net weight: 6g
Reference: RBD-0391
Designed to extract, amplify, and filter small biopotential signals. Leads-Off Detection. Shutdown Pin. LED Indicator. Analog Output. 3.5 mm Jack for Biomedical Pad Connection. RoboticsBD
Reference: RBD-0576
Chipboard STM32F103C8T6 On board, SWIM interface and reset button Micro USB line or the 2.54 pin to link to the power with the input voltage 4.5V-15V. Power light and the Demo indicator light Leads all the pins and has detailed label for the Pins. Support SWIM debug mode. RoboticsBD
Reference: RBD-0439
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....
Reference: RBD-0416
Onboard 8 key TTP226 capacitive touch induction IC. RoboticsBD Onboard 8-way level indicator. Working voltage: 2.4 to 5.5 V. Modules, you can set the output mode, key output mode, the longest time and fast/low power output
Reference: RBD-0163
Product Type: Humidity Module Sensor Working voltage range DC 5.0±0.2V Output voltage range (corresponding to 0-100%RH) DC 1-3.19V Test accuracy 5% RH
Reference: RBD-0425
Model: GY-APDS9960-3.3 Chip: APDS-9960 Power Supply: 3.3VDC Communication Through I2C Protocol. RoboticsBD
Reference: RBD-0990
Support any Chinese text, English text synthesis, and support for English mixed Support voice codec function, the user can use the chip for direct recording and playback Support speech recognition function, can support the recognition of 30 command words.