• How to Place an Order

  • bKash Payment Method

  • Request for Quotation/ International Sourcing

Arduino Uno R3

Arduino UNO in Bangladesh The Arduino Uno is a microcontroller board based on the ATmega328 (datasheet). It has 14 digital input/output pins (of which 6 can be used as PWM outputs), 6 analog inputs, a 16 MHz ceramic resonator, a USB connection, a power jack, an ICSP header, and a reset button. It contains everything needed to support the microcontroller.

Price BDT 399
More
In Stock

BreadBoard

Solderless Large BreadboardA breadboard (or protoboard) is usually a construction base for prototyping of electronics. The term "breadboard" is commonly used to refer to a solderless breadboard (plugboard). Because the solderless breadboard for electronics does not require soldering, it is reusable. This makes it easy to use for creating temporary...

Price BDT 95
More
In-Stock
All best sellers
RC522 RFID Card Reader Module Kit Android NFC supported
  • RC522 RFID Card Reader Module Kit Android NFC supported

RC522 RFID Card Reader Module Kit Android NFC supported

Specification:

  • Module Name: MF522-ED
  • Working current:13—26mA/ DC 3.3V
  • Standby current:10-13mA/DC 3.3V
  • sleeping current:<80uA
  • peak current:<30mA
  • Working frequency:13.56MHz
  • Card reading distance :0~60mm(mifare1 card)
  • Protocol:SPI
  • data communication speed:Maximum 10Mbit/s
BDT 180
rating No review at the moment
Quantity
In-Stock

  • Store Pickup Available! Store Pickup Available!
  • Shipping Available Shipping Available
Description

Product Description

RC522 IC Brief Introduction

MF RC522 is used in highly integrated 13.56MHz contactless communication card chip to read and write, of NXP for “three” and the application launched a low voltage, low cost, small size, non-contact card chip to read and write, intelligent instruments and portable handheld devices developed better.

The MF RC522 use of advanced modulation and demodulation concept completely integrated in the 13.56MHz all kinds of passive contactless communication methods and protocols. 14443A compatible transponder signal. The digital part handles the the ISO14443A frames and error detection. In addition, support Quick CRYPTO1 encryption algorithm, the term verification MIFARE series. MFRC522 support MIFARE series of high-speed non-contact communication, two-way data transfer rates up to 424kbit / s.

As 13.56MHz highly integrated card reader series chip new family, the MF RC522 MF RC500 MF RC530 there are many similarities, but also have many of the characteristics and differences. Communication between it and the host SPI mode, helps to reduce the connection, reduce PCB board volume and reduce costs.

RFID Module Brief Introduction

MFRC522-AN module uses Philips MFRC522 original chip design circuit card reader, easy to use, low cost, suitable for equipment development, the development of advanced applications reader users, the need for RF card terminal design / production users. This module can be directly loaded into the variety of reader molds.Module uses voltage of 3.3V, simple few lines through the SPI interface directly with any user CPU board is connected to the communication module can guarantee stable and reliable work, reader distance.

Features: 13.56Mhz, S50, Mifare One

Specification:

  • Module Name: MF522-ED
  • Working current:13—26mA/ DC 3.3V
  • Standby current:10-13mA/DC 3.3V
  • sleeping current:<80uA
  • peak current:<30mA
  • Working frequency:13.56MHz
  • Card reading distance :0~60mm(mifare1 card)
  • Protocol:SPI
  • data communication speed:Maximum 10Mbit/s
  • Card types supported:mifare1 S50、mifare1 S70、mifare UltraLight、mifare Pro、mifare Desfire
  • Dimension:40mm×60mm
  • Environment
  • Working temperature:-20—80 degree
  • Storage temperature:-40—85 degree
  • Humidity:relevant humidity 5%—95%
  • Max SPI speed: 10Mbit/s

Packaging:

  • RFID-RC522 Module *1
  • Standard empty RC522 Card *1
  • RC522 Key *1
  • Break away pin straight *1
  • Break away pin 90 degree *1
 

Documentation:

Product Details
31 Items

Click here to leave a review

30 other products in the same category:

PIC Development Board with Cable PIC16F877

1. Reset button. 2. 4M crystal onboard, Using socket, Crystal frequency can be replaced easily at any time 3. 4 independent push buttons, connected to RB0 RB1 RB2 RB3 4. 8 LED's connected to the RD port, J3 is jumpered to enable LED. Remove to disconnect. 5. Standard RS232 communication interface, microcontroller computer communication interface. 6. USB...

Price BDT 1,200
More
In-Stock

9 Degrees of Freedom Breakout- MPU9150

The 9DOF MPU-9150 is the world’s first 9-axis MotionTracking MEMS device designed for the low power, low cost, and high performance requirements of consumer electronics equipment including smartphones, tablets and wearable sensors. And guess what? You get to play with it.

Price BDT 2,000
More
In Stock

XBee USB Adapter

Specifications: - 3.3V and 5V dual power output- 3.3V and 5V IO compatible- USB2.0 protocol- BitBang mode ready- Easily connected to PC via mini USB cable- Support XBee-setting with software X-CTU

Price BDT 1,200
More
In-Stock

I2C LCD Adapter Module

As the pin resources of Arduino controller is limited, your project may be not able to use normal LCD shield after connected with a certain quantity of sensors or SD card. However, with this I2C interface LCD module, you will be able to realize data display via only 2 wires. If you already has I2C devices in your project, this LCD module actually cost no...

Price BDT 145
More
In Stock

Arduino Ethernet Shield W5100

Arduino Etherner Shield in Bangladesh The Arduino Ethernet Shield connects your Arduino to the internet in mere minutes. Just plug this module onto your Arduino board, connect it to your network with an RJ45 cable (not included) and follow a few simple instructions to start controlling your world through the internet.

Price BDT 600
More
In Stock

Reference: SIM900A

ATK-SIM900A GSM /GPRS Module

Fully Arduino and Microcontroller Compatible ◾ GSM module: SIM900A ◾ RTC backup battery ◾ A microphone port ◾ A headphone jack ◾ RS232 interface selection ◾ RS232 serial port ◾ lithium battery Interface ◾ power input connector ◾ power LED (blue) ◾ power switch ◾ SIM card Slot ◾ SMA antenna interfaces and supporting small antenna ◾ Power On / Off button ◾...

Price BDT 4,000
More
Pre Order

Brand: DFRobot

Arduino GPS/GPRS/GSM Shield V3.0

INTRODUCTION This is a Arduino GPS/GPRS/GSM shield from DFRobot. This shield with a Quad-band GSM/GPRS engine works on frequencies EGSM 900MHz/DCS 1800MHz and GSM850 MHz/PCS 1900MHz. It also supports GPS

Price BDT 7,200
More
Pre-Order

Arduino 3G+Wifi+Ethernet Shield

Iduino Yun Shield Compatible with Arduino Leonardo, Uno, Duemilanove, Diecimila and Mega Arduino 3G+Wifi+Ethernet Shield Robotics Bangladesh 3g+ Wifi+ Ethernet + USB+ Openwrt (Linux) Geeetech Latest Iduino Yun Shield board Linux WiFi 3G Ethernet USB for Arduino http://www.geeetech.com/wiki/index.php/Iduino_Yun_Shield

Price BDT 5,500
More
Pre-Order

4x4 Keypad - 16 Key - Matrix Membrane Type

4 x 4 Matrix Membrane Keypad Size: 7cm X 7.5cm 8 pin connector Adhesive mounting (sticker on the back side) Maximum Circuit Rating: 35VDC, 100mA Operation Temperature: 0 to +60 centigrade Humidity: 40 centigrade, 90%-95%, 240 hours Fexible Circuit Length: Approx. 3.3 inch / 83 mm

Price BDT 90
More
In-Stock

Arduino Ethernet Shield Basic

Arduino Ethernet Shield in Bangladesh - With this Ethernet Shield, your Arduino board can be connected to internet- Uses ENC28J60 SPI Ethernet controller and compatible HR911102A RJ45 socket- Web client application to use Arduino as a distributed network sensor- Stackable by accepting prototype shield or any other boards with Arduino compatible interface

Price BDT 1,900
More
There are not enough products in stock

Brand: DFRobot

Xbee Shield for Arduino (without Xbee)

Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.

Price BDT 1,200
More
Last items in stock

JoyStick 5Pin Breakout Module For Arduino

Specification:  Brand new Color: as picture shows Size: approx. 34 x 26 x 32mm       (L x W x H) Quantity: 1pc PS2 joystick joysticks standard       interface module electronic building blocks and 2.54mm pin interface leads

Price BDT 150
More
In-Stock

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino

AC 0~5A Analog Current Meter Module Ammeter Sensor Board for Arduino This electricity sensor is based on TA12-100 current transformer, which can transform AC signals of large current into small amplitude signals. The maximum current that can be detected can reach 5A, and the present current signal can be read via analog I / O port.

Price BDT 900
More
In-Stock

Follow us on Facebook