How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-2436
Brand: Creality Official
Creality Ender-3 V3 SE 3D Printer Max printing speed of 250mm/s and 2500mm/s² acceleration Auto leveling with CR Touch & Strain Sensor for precise prints "Sprite" Direct Extruder for PLA, PETG, and flexible TPU Stable Dual Z-axis and Y-axis Dual Linear Shafts for reliable printing Auto filament loading and unloading for easy filament changes
Reference: RBD-0815
Input Voltage: 100-240 V AC. Temp: 160~230 Deg settable. Filament: 1.75 mm PLA or ABS. This 3D Pen is designed for the freehand drawing of 3-Dimensional objects Adjustable output speed, temperature Create projects horizontally or vertically Every 3d pen will be checked and tested on our lab before shipping, so you will not received "intact" package. No...
Reference: RBD-2437
Brand: Creality Official
Build area: 300 x 300 x 400 mm Maximum print head temperature: 300°C Maximum bed temperature: 100°C Communication: WiFi, USB Supported materials: PLA, ABS, PETG, TPU, PA, and carbon fiber composites.
Reference: RBD-1163
The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.
Reference: RBD-1733
Brand: Creality Official
Built-in WIFI function: Remote control printing anytime, anywhere; A Bit More Intelligence Ultra-silent Design: 32 Bit Mute Board and Mute Fan Design; Intelligent Auto-leveling: V2.0 Auto leveling way, is the same with CR-6 SE. Screen Protection & Auto-shutdown;. Safe and worry-free save energy and power. 6-steps to assemble 8 minutes to complete,...
Reference: 1403
Brand: Creality Official
Replaced with New Version Creality Ender-3 V3 SE 3D Printer. Click Here
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-0356
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: 1404
Brand: Creality Official
Modeling Technology: FDM（Fused Deposition Modeling） File Formats: STL/OBJ/AMF Slicer Software: Creality Slicer/Cura/Reptier-Host/Simplify3D Print Speed: 80-100mm/s Resume Print Function: Yes Printing Size: 235x235x250mm
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: 1375
Brand: Anycubic
Technique: LCD-based SLA Printing Speed: 30mm(H)/hour Power: 30W
Reference: 1316
Tougher and stronger Less warping (about 0.4% compared to over 8% in regular ABS) Prints smoother & smoother printed objects Better scratch, heat and oil resistance Can be polished using acetone Can be easily colored.
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: 1315
Great bio-compatibility, excellent transparency and environment-friendly Low shrinkage, good round shape Accurate diameter (±0.02mm) Easy to print with stable printing performance Various colors are available 100% bio-degradable and FDA food safety approved
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: 1391
TPU rubber based Material. Very flexible and elastic. Shore A Hardness at 87A. Tensile Strength 52 MPa.
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: 1392
PETG Filament Plastic For 3D Printer 1.75mm1KG/Roll Compatible with Anycubic, Creality. Temperature: 205-230 °C Bed Temperature: 60-80 °C
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: 1317
TPU rubber based Material. Very flexible and elastic. Shore A Hardness at 87A. Tensile Strength 52 MPa.
Reference: RBD-0269
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 8 jumper wires (8-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-1386
Brand: Anycubic
Wavelength(nm): 395-405 Color: Black Density(g/m^3): 1.08-1.13 Hardness(Shore D):79.0 Tensile Strength(MPa): 46-67 Elongation at Break(%):28-35
Reference: RBD-1227
Object Scanning Device with USB 2.0 Interface / CMOS Sensor
Reference: RBD-0727
Operating Voltage: 12VDC Power Consumption: 1.42 W Body and Blade Constructed from Thermoplastic PBT of UL 94V-0 Single Phase 4 Pole Brushless DC Motor Precise Vapo Bearing Counterclockwise Rotation Direction if Viewed from front of Fan Blade
Reference: RBD-0436
Supply Voltage: 12V Standard interfaces (as that of the extruder) Reserved GCI like I2C and RS232 3 MOSFET’s are applied to the heater/ fan and thermistor circuit. Another 5A added to protect the component parts. An 11A fuse is added to the hotbed. Support 5 stepper drive board
Reference: RBD-2182
Filament Support: 1.75mm Material: High-quality brass Color: Brass color Screw outer diameter: M7 If you are not sure which Nozzle size to choose, Please check our guide in the documentation tab below.
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-2534
3D-printed robotic arm with 4 stepper motors and 1 servo motor for precise control Robot arm size: approximately 25 x 13 x 29 cm Features claws for easy gripping Includes all necessary 3D-printed parts and motors The color and claw mechanism of the Robotic arm may vary as our stock rotates. Current stock comes as assembled.
Reference: RBD-0435
Supply Voltage : 8-35 VDC. Current : 1.0A (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.
