How to Place an Order
Store Pick Up
Request for Quotation/ International Sourcing
Order Status
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Subcategories
Reference: RBD-0166
Description: This is the very popular 2.4GHz XBee module from Digi. These modules take the 802.15.4 stack (the basis for Zigbee) and wrap it into a simple to use serial command set. These modules allow very reliable and simple communication between microcontrollers, computers, systems, really anything with a serial port! Point to point and multi-point...
Reference: RBD-0268
Brand: RoboticsBD
Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R
Reference: RBD-0286
3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included
Reference: RBD-0369
Brand: SparkFun Electronics
Supports binding and multicasting for home automation Mesh-network topology 2.4 GHz for worldwide deployment Common XBee footprint fits Parallax XBee Adapters and the Propeller Activity Board Firmware upgrades via UART, SPI or over the air TRANSCEIVER CHIPSET: SiliconLabs EM357 SoC DATA RATE: 250kbps Max RATED OUTDOOR/RF LINE-OF-SIGHT RANGE: Up to 2 mile...
Reference: RBD-2500
Processor: Intel Core i5 3470 Motherboard: H61 Bus Specs: PCI-Express 2.0 (5.0GT/s) Chipset: Intel Ivy Bridge RAM: DDR3 8GB Casing: 0.6mm SECC Mini ITX Black Chassis
Reference: RBD-0189
Brand: DFRobot
Xbee Shield for Arduino (without Xbee) INTRODUCTION: The XBee Expansion Board is a compliant solution designed to meet low-cost, low-power wireless sensor networks with special needs.The module is easy to use, low power consumption, and the provision of critical data between devices reliable transmission.
Reference: RBD-0815
Input Voltage: 100-240 V AC. Temp: 160~230 Deg settable. Filament: 1.75 mm PLA or ABS. This 3D Pen is designed for the freehand drawing of 3-Dimensional objects Adjustable output speed, temperature Create projects horizontally or vertically Every 3d pen will be checked and tested on our lab before shipping, so you will not received "intact" package. No...
Reference: RBD-1593
১ টি রাস্পবেরি পাই 4 (Made in UK) RAM: 1GB, 2GB, 4GB, 8GB (পছন্দ করে নিতে পারবেন) একসাথে দুটি HDMI মনিটর লাগানো যায়। ১ টি Argon One V2 Case কেস। রাস্পবেরি পাই এর ইউএসবি -সি পাওয়ার এডাপটার সুইচ সহ। ট্রান্সসেন্ড অথবা স্যানডিস্ক ব্রান্ডের জেনুইন ১৬ জিবি অথবা ৩২ জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ। বিল্ট ইন Wi-Fi & Bluetooth গিগাবিট...
Reference: RBD-0400
Voltage: 3-3.6V (recommended 3.3V) V. Maximum output power: +20dBm. Power-down mode current: 4.2uA. Operating Range: 1Km Antenna Gain (peak): 2Dbi. 2MB rate (Open area): 520m. 1MB rate (Open area): 750m. 250Kb rate (Open area): 1100m. It uses 2.4GHz global open ISM band, with license free. SPI interface facilitates the communication with MCU I/O port....
Reference: RBD-1163
The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.
Reference: RBD-1519
Brand: Raspberry Pi Official
Quad-Core 64-bit Broadcom 2711, Cortex A72 Processor WLAN 802.11 b/g/n/ac (2,4 + 5,0 GHz) LAN RJ45 10/100/1000 Mbit (Gigabit LAN over USB 3.0) Operating Power 5V@3A via USB Type-C port. Keyboard Layout: US Dual-Display Micro HDMI Ports which supports H 265 Decode for 4K Video @60p Built-in Raspberry Pi Official Keyboard
Reference: RBD-0196
Brand: DFRobot
The APC220 radio module offers a cost-effective solution for wireless data communications, featuring an embedded high-speed microprocessor and high-performance IC. With its transparent UART/TTL interface, it eliminates the need for packetizing and data encoding, making it a popular choice among customers seeking better range performance at a low cost.
Reference: RBD-1373
GPU: 128-core NVIDIA Maxwell™ GPU CPU: Quad-core ARM® A57 CPU Memory: 4 GB 64-bit LPDDR4 Storage: 16GB eMMC 5.1 flash Video Encoder: 4K @30（H.264/H.265） Video Decoder: 4K @60（H.264/H.265） Camera: 12 lanes (3×4 or 4×2) MIPI CSI-2 DPHY 1.1（1.5Gbps） Connectivity: Gigabit Ethernet Display: HDMI 2.0 or DP1.2 |eDP 1.4| DSI (1x2) UPHY: 1x1/2/4 PCIE, 1xUSB3.0,...
Reference: RBD-1683
Compatible with 3D pen 15gram-17gram 1.75mm Random Color
Reference: RBD-0237
Description: This Telemetry radio set allows you to link to a flight controller such as the APM or Multiwii AIO via a USB equipped device such as a computer, laptop or tablet supporting a USB connection (OTG). APM /Pixhawk Radio Telemetry Kit 433Mhz 100mW (OTG Cable Included)
Reference: RBD-0356
PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.
Reference: RBD-0934
Processor: Intel J1800 2.41Ghz Processor RAM: 2GB DDR3L SSD: 32GB mSata Built-in Wi-Fi with Dual Antenna 2xUSB 3.0 & 2xUSB 2.0 Dual RJ45 Network Port/ LAN Pre-Installed Windows 10 SATA Port: Yes Solid Industrial Grade Aluminum Casing Dual Serial Port (RS232) Windows 10 Pre-Installed. Power Input: DC12V
Reference: RBD-0389
Adopt imported controller PL2303HX, which can stabilize the flash with high speed 500mA self-recovery fuse for protection Two data transmission indicator can monitor data transfer status in real time Reserve 3.3V and 5V pin interface, easy for the DDWRT of different voltage system that needs power The entire board is coated by the high quality transparent...
Reference: RBD-0935
J1800 Windows 10 Pro Mini PC 2GB RAM + 32GB SSD (V2) Processor: Intel J1800 2.41Ghz Processor RAM: 2GB DDR3L SSD: 32GB mSata Built-in Wi-Fi with Dual Antenna 1xUSB 3.0 & 4xUSB 2.0 RJ45 Network Port/ LAN Pre-Installed Windows 10 SATA Port: Yes Solid Industrial Grade Aluminum Casing Windows 10 Pre-Installed. Power Input: DC12V
Reference: RBD-1364
10 mm LED light strips. Attached with a nail or a screw.
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: 1141
Brand: Raspberry Pi Official
১ টি রাস্পবেরি পাই 4 (Made in UK) RAM: 1GB, 2GB, 4GB, 8GB (পছন্দ করে নিতে পারবেন) একসাথে দুটি HDMI মনিটর লাগানো যায়। ১ টি কুলিং অ্যালুমিনিয়াম মেটাল ফ্যান কেস। রাস্পবেরি পাই এর হিট সিংক। রাস্পবেরি পাই এর ইউএসবি -সি পাওয়ার এডাপটার সুইচ সহ। ট্রান্সসেন্ড অথবা স্যানডিস্ক ব্রান্ডের জেনুইন ১৬ জিবি অথবা ৩২ জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ।...
Reference: RBD-0251
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0439
Bluetooth Protocol: Bluetooth Specification V4.0 BLE USB Protocol: USB V2.0 Operating Frequency: 2.4GHz ISM band Modulation Mode: GFSK (Gaussian Frequency Shift Keying) Transmitting Power: ≤4dBm Sensitivity: ≤-84dBm at 0.1% BER It’s easy to use and completely encapsulated. You can set it as slave or master. You can use AT command set the baud rate....
Reference: 0746
Out of Stock ১ টি রাস্পবেরি পাই ৩ মডেল বি প্লাস ১ টি কুলিং ফ্যান কেস রাস্পবেরি পাই এর হিট সিংক রাস্পবেরি পাই এর কমপ্যাটিবল পাওয়ার এডাপটার সুইচ সহ ট্রান্সসেন্ড অথবা স্যানডিস্ক ব্রান্ডের জেনুইন 32 জিবি অথবা 64 জিবি মেমরি কার্ড প্রি-ইনস্টলড অপারেটিং সিস্টেম সহ।
Reference: RBD-0040
Bases at CSR BC04 Bluetooth technology. with build-in 2.4GHz PCB antenna It’s at the Bluetooth class 2 power level. Range test: 10 meters Operating voltage: 3.3V to 6V DC Operating current in pairing is in the range of 30~40mA.
Reference: RBD-0260
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-2376
Rockchip RK3588S 8-core 64-bit processor Quad-core A76 + quad-core A55 architecture ARM Mali-G610 GPU with 3D/2D image acceleration Built-in NPU with 6Tops computing power 4GB LPDDR4 RAM Up to 8K display processing capability
Reference: RBD-0262
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
Reference: RBD-0284
Gain: 2.0dBi-2.5dBi Antenna connector: RP-SMA Male Connector Standing wave ratio(SWR): <1.5 Weight: TxA10.3g, RxA 11.5g TxA is a circular-polarized Omni antenna with three lobes RxA is a circular-polarized Omni antenna with four lobes
Reference: RBD-2375
Rockchip RK3399(28nm HKMG Process) 6-core ARMR64-bit processor 4GB LPDDR4 SDRAM, 16GB EMMC Flash HDMI output, 26-pin headers, LCD connector, 2USB 2.0, 1USB 3.0, 1*USB 3.0 TYPE-C, mini PCIE connector, etc. Support for dual cameras, binocular vision ranging, power management, TF card storage, SATA and SSD expansion, LED indicator Low-level peripherals...
Reference: RBD-0263
Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.
