Reference: RBD-0015

Motor Shield L293D

96 reviews

2 connections for 5V ‘hobby’ servos connected to the Arduino’s high-resolution dedicated timer 4 H-Bridges: L293D chipset provides 0.6A per bridge (1.2A peak) with thermal shutdown protection, internal kickback protection diodes. Can run motors on 4.5VDC to 25VDC. Up to 4 bi-directional DC motors with individual 8-bit speed selection (so, about 0.5%...

Reference: RBD-0954

XTAR VC2 Charger with LCD Screen Display for 18650 26650 Battery

4 reviews

Tell you the real capacity of your battery! LCD display show all info you want Micro-USB powered, charge everywhere at your will Charge all popular Li-ion batteries Unique efficient charge method (TC-CC-CV) with 0.5Ax2.

Reference: RBD-0267

Big Easy Driver - Stepper Motor Driver

1 review

Bi-polar Microstepping Driver 2A/Phase Max 1.4-1.7A/Phase w/o Heatsink Max Motor Drive Voltage: 30V On-board 5V/3.3V Regulation Low RDS(ON) outputs Automatic current decay mode detection/selection Mixed and Slow current decay modes Synchronous rectification for low power dissipation Internal UVLO Crossover-current protection 3.3 and 5 V compatible logic...

Reference: RBD-0955

XTAR VC4 Charger for Lithium-ion and Ni-MH Batteries

11 reviews

Clearly see what’s going on with the batteries. Tachometer-style LCD display shows detailed charging status Powered by any 5V USB power Intelligently chooses charging currents from 0.1A to 1A Wide adaptability, adapts from 10440 to 32650, from Li-ion to Ni-MH Energy-saving LCD backlight, can be turned off at your will.

Reference: RBD-1565

Robotic Arm Edge Kit

1 review

MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm

Reference: RBD-0289

16 Channel 12 bit PWM / Servo Driver I2C interface PCA9685

14 reviews

Adjustable frequency PWM up to about 1.6 KHz 12-bit resolution for each output – for servos, that means about 4us resolution at a 60Hz update rate Configurable push-pull or an open-drain output The output enable pin to quickly disable all the outputs Terminal block for power input Reverse polarity protection on the terminal block input Green power-good LED

Reference: RBD-0836

14500 Rechargeable Lithium Battery 1300mah 3.7v

65 reviews

Model: 14500 Type: Li-Ion Battery Mark Capacity: 850mah Nominal Voltage: 3.7v Color:    Blue    Weight: 17g Rechargeable Battery: Yes Note: It's a clone battery so the ampere couldn't be guaranteed.

Reference: RBD-1244

Hiwonder 6DOF Metal Robotic Arm with Controller

1 review

Aluminum body with high torque metal gear servos 6 DOF structural design makes the robot arm move flexibly Up to 17Kg torque for joint servos Various control ways

Reference: RBD-0306

Torobot 32 Channel USB UART Servo Motor Controller

1 review

Baud rate (USB): 115200 Baud rate (bluetooth, UART): 9600 Storage Flash capacity: 16M Mode to choose: 4 types Simultaneous controlling servo number: 32 channel Max action groups: 256 groups Communication agreement: UART Cross platform operation, can support WindowsXP, WindowsVisit, Windows7, Windows8, Windows10, Linux,FreeBsd, MAC OS, Android

Reference: RBD-0925

18650 Battery Holder 4S with wire

26 reviews

Hold 4 standard 18650 batteries. Wire Length: 15 cm. Output: 14.8 V. Dimension (Appro.) : 80 x 76 x 18 mm. Weight: 28 gm. High-quality plastic material

Reference: RBD-2123

xArm 1S Intelligent Bus Servo Robotic Arm Manipulator for Programming

1 review

STM32 chip for the main controller Easy Visual Operation Interface Support wireless handle control, smart phone APP and mouse control Provide graphical PC software and detailed tutorials The current Stock comes unassembled.

Reference: RBD-0375

Lynxmotion AL5D 4DOF Robotic Arm SSC-32U Combo Kit (FlowBotics Studio)

AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)  

Reference: RBD-0376

L298N H-Bridge Dual Motor Driver, Stepper Motor Driver

137 reviews

Current Sense for each motor. RoboticsBD Heatsink for better performance. Power-On LED indicator. Double H bridge Drive Chip: L298N. Operating Voltage(VDC): 5~35 Peak Current (A): 2 Continuous Current (A): 0-36mA No. of Channels: 2 Over-Current Protection (A): Yes Thermal Protection: Yes

Reference: RBD-0837

18650 Li-ion Rechargeable Battery

78 reviews

Capacity (mAh): 960-1500 Output Voltage: 3.7V High energy density High working voltage for single battery cells. Pollution-free Long cycle life ***It's a clone battery so the ampere couldn't be guaranteed. RoboticsBD

Reference: RBD-0377

Monster Moto Shield Dual VNH2SP30 Motor Driver Module 30A

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0652

Battery 9V

119 reviews

Constant 9V Output till lasts Metal Jacket Body Good Built Quality and hence Leakproof Easy to install and Replace Corrosion free Connector Point for long-term use 0% Mercury and Cadmium. Environment-friendly OEM Compatible. RoboticsBD

Reference: RBD-2045

DIY D2-1 Intelligent Line follower/Tracking Smart Car Kit

Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included

Reference: RBD-0392

Ardumoto Shield L298P Motor Driver

L298P based Arduino motor driver shield Forward, Backward steering indicators Can Drive 2 DC Motors Up to 2A of Maximum Current. RoboticsBD

Reference: RBD-0651

9V Battery Connector

82 reviews

Made of hard leather. Excellent material, fine workmanship. It is an environmental 9V battery buckle. Wire Length: 5cm. Color: Black.

Reference: RBD-2251

BALA-C PLUS ESP32 Self-Balancing Robot Kit

ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38

Reference: RBD-0434

DRV8825 Stepper Motor Driver Module

5 reviews

Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD

Reference: RBD-0732

9V Battery to 2.1mm for Arduino Uno

94 reviews

Excellent material It is an environmental 9V battery buckle The Cable Length: 12cm Approx. Convenient for connecting a battery to your application. Save power and protect the environment Good electrical conductivity and comfortable sense of touch

Reference: RBD-1254

XiaoR STM32 Self Balancing Programmable Robot

Size: 202X85X200mm Weight: 1150 gram MCU: STM32F105 Motor Drive: LV8731 motor driver chip Charging Direct

Reference: RBD-0435

A4988 StepStick Stepper Motor Driver Module

2 reviews

Supply Voltage : 8-35 VDC. Current : 1.0A  (no heatsink ). Current : 2.0A (with heat-sinking). logic input : 3 – 5.5V . Automatic current decay mode detection / choice. Mixed with slow current decay mode.

Reference: RBD-0763

AA Battery Holder 2s

44 reviews

Cell Quantity: 2 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC

Reference: RBD-1253

Wuli bot Programmable Robot

1 review

Program Software: Mixly + XR Scratch(base on Scratch2.0) Input: Edge sensor, Button, IR receiver module, Ultrasonic sensor, Tracking sensor Output: Buzzer, RGBLED, Two motor port,OLED CPU: Arduino UNO R3 Power: 2Pcs 3.7V DC Lithium battery Control: WiFi control/IR remote

Reference: RBD-0557

30A Mini VNH2SP30 Stepper Motor Driver Monster Moto Module For Arduino

Voltage Max: 16V Maximum current rating: 30 A Practical Continuous Current: 14 A Current sensing available to Arduino analog pin MOSFET on-resistance: 19 mΩ (per leg) Maximum PWM frequency: 20 kHz Thermal Shutdown Undervoltage and Overvoltage shutdown. RoboticsBD

Reference: RBD-0764

AA Battery Holder 3S

28 reviews

Cell Quantity: 3 Battery type: AA Storage temperature: 25ºC Max Operate temperature: 80ºC

Reference: RBD-1129

Brand: RoboticsBD

Otto Bot Complete

1 review

Complete Assembled  Plug and Play Open Source Design Compatible With Arduino IDE DIY Kit

Reference: RBD-0573

DC 5V Stepper Motor with ULN2003 Driver Board 28BYJ-48

21 reviews

Rated voltage: 5V DC Reduction Ratio: 64:1 Step Angle: 5.625° /64 Frequency: 100Hz Self-positioning Torque: >34.3mN.m Friction torque: 600-1200 gf.cm Pull in torque: 300 gf.cm

Reference: RBD-0765

AA Battery Holder 4S

18 reviews

Holds 4 AA batteries Easy install, convenient to use. Dimensions mm (LxWxH): 62 x 58 x 15 Weight: 15 gm Material: Plastic Internal Connection: Series

Reference: RBD-1252

Makeblock mBot Ranger 3-in-1 educational robot kit

Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes