Reference: RBD-0268

Brand: RoboticsBD

3D Printed Robotics claw with servo motor

Description: Material: PLA (3D Printed)Claw max angle: 55mmLength: 108mmWidth: 98mm (streched)Color: Golden, Blue, Red Servo Motor: MG996R

Reference: RBD-0286

Arduino Uno R3 Bumper

4 reviews

3D Printed Arduino Uno R3 Bumper or base.Short Circuit Prevention: Safeguard your microcontroller against the risk of short circuits when placing it on a flat conductive surface. The bumper acts as a protective barrier, reducing the chances of accidental electrical contact. Note: Arduino Uno is not included

Reference: RBD-0694

ESP8266 CH340 NodeMCU Wifi Module Lua V3

120 reviews

Power input: 4.5V ~ 9V (10VMAX), USB-powered Transfer rate: 110-460800bps Support UART / GPIO data communication interface Support Smart Link Smart Networking Working temperature: -40°C ~ + 125°C Drive Type: Dual high-power H-bridge Don’t need to download resetting A great set of tools to develop ESP8266 Flash size: 4MByte Lowest cost WI-FI Note: The...

Reference: RBD-1565

Robotic Arm Edge Kit

1 review

MODEL: Robotic Arm Edge Kit based on OWI-535 WEIGHT: 4.00kg DIMENSIONS: 40.00cm x 30.00cm x 8.50cm

Reference: RBD-0815

3D Pen 2nd Generation LED Display Screen with (6 Color Filament)

6 reviews

Input Voltage: 100-240 V AC. Temp: 160~230 Deg settable. Filament: 1.75 mm PLA or ABS. This 3D Pen is designed for the freehand drawing of 3-Dimensional objects Adjustable output speed, temperature Create projects horizontally or vertically Every 3d pen will be checked and tested on our lab before shipping, so you will not received "intact" package. No...

Reference: RBD-1244

Hiwonder 6DOF Metal Robotic Arm with Controller

1 review

Aluminum body with high torque metal gear servos 6 DOF structural design makes the robot arm move flexibly Up to 17Kg torque for joint servos Various control ways

Reference: RBD-1407

ESP32-CAM WiFi + Bluetooth Camera Module Development Board ESP32 With Camera Module OV2640

32 reviews

Flash LED off: 180mA @ 5V. Flash LED on to maximum brightness: 310mA @ 5V. Deep-sleep: 6mA @ 5V min. Modem-sleep: 20mA @ 5V min. Light-sleep: 6.7mA @ 5V min. Programmer: ESP32-CAM-MB MICRO USB Download Module The ESP32 CAM does not come pre-assembled with the camera. You'll need to connect the camera ribbon cable to the board, a task which can be...

Reference: RBD-0948

ESP32 ESP-32S 30P NodeMCU Development Board Wireless WiFi

32 reviews

Built-in Flash: 32Mbit Power supply: 5V WiFi protocol: IEEE 802.11 b/g/n Peripheral interface: UART/GPIO/ADC/DAC/SDIO/PWM/I2C/I2S Logic level: 3.3V

Reference: RBD-1163

Robotics Arm EEZYbotARM MK1

The design intent was to make something "easy" to make robotics arm It uses Mini servos for driving the kinematics linkage and you can use Arduino and a decent power supply (2A) to program and drive it. All the pieces are 3DPrinted in PLA.

Reference: RBD-2123

xArm 1S Intelligent Bus Servo Robotic Arm Manipulator for Programming

1 review

STM32 chip for the main controller Easy Visual Operation Interface Support wireless handle control, smart phone APP and mouse control Provide graphical PC software and detailed tutorials The current Stock comes unassembled.

Reference: RBD-0375

Lynxmotion AL5D 4DOF Robotic Arm SSC-32U Combo Kit (FlowBotics Studio)

AL5D arm with SSC-32U USB board and powerful PC software Advanced inverse kinematics positioning control using mouse Includes license for full version of FlowBotics Studio Programming Software Wrist rotate sold separately (three options)  

Reference: RBD-1138

AI-thinker A9G GSM/GPRS+GPS/BDS Development Board

4 reviews

Board Based On AI-Thinker A9 GPRS Module Supports Firmware Upgrade Via Serial Port Operating Voltage: 5v

Reference: RBD-1683

PLA Filament for 3D Pen

3 reviews

Compatible with 3D pen 15gram-17gram 1.75mm Random Color

Reference: RBD-0356

Abs Material 2 Axis Pan Tilt Camera Mount With MG90

1 review

PV Nylon Head Two Axial plastic Two axial platform Anti-vibration lightweight Good design and shape Net weight 20g Color : Black Material: Plastic.

Reference: RBD-0552

A6 Pro Serial GPRS GSM Module Core Development Board

9 reviews

Working frequency: quad-band network, 850 / 900 / 1800 / 1900MHz Working voltage: 4.8-9VDC(On-board voltage regulator circuit supply power for A6 module) Working Current: maximum of 2A. RoboticsBD

Reference: RBD-2045

DIY D2-1 Intelligent Line follower/Tracking Smart Car Kit

Easy to Assemble comes as disassembled. Soldering is Required. Operating Voltage: 3V Line Map included Note: Batteries not included

Reference: RBD-1039

SIM800L Mini GPRS GSM Module

40 reviews

The module was recycled from a mobile phone so you can say it is used. TTL serial port for serial port, you can link directly to the micro-controller. Don’t need MAX232. Power module automatically boots, homing network. Onboard signal lights all the way. It flashes slowly when there is a signal, it flashes quickly when there is no signal. In recent years...

Reference: RBD-1364

Holder for 10 mm LED light strip

10 mm LED light strips. Attached with a nail or a screw.

Reference: RBD-2251

BALA-C PLUS ESP32 Self-Balancing Robot Kit

ESP32-Pico-D4: 240MHz dual-core, 600 DMIPS, 520KB SRAM, Wi-Fi, dual mode Bluetooth Servo Rotation angle: 360 °; no-load speed: 0.12 seconds / 60 degrees (4.8V) Driver: L9110S Slave: STM32F030F4P6 Communication protocol I2C: 0x38

Reference: RBD-1037

SIM808 GPRS/GSM+GPS Shield

1 review

Quad-band 850/900/1800/1900MHz Inner MT3337 GPS receiver, -165dBm precision, control on a same serial port. Earphone/ microphone outputs on a card or external 32-ohm speaker + supports voice calls with an electret microphone. Sending and receiving SMS.

Reference: RBD-1254

XiaoR STM32 Self Balancing Programmable Robot

Size: 202X85X200mm Weight: 1150 gram MCU: STM32F105 Motor Drive: LV8731 motor driver chip Charging Direct

Reference: RBD-0251

Jumper Wire housing 3 Pin

1 review

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 3 jumper wires (3-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0318

SIM900A Mini Module 5V

10 reviews

This module is intended for advanced users who require moderate knowledge of GSM systems and microcontrollers. It needs wiring and firmware updates to unlock the country lock.  Dual-Band 900/ 1800 MHz GPRS multi-slot class 10/8GPRS mobile station class B Compliant to GSM phase 2/2+ Dimensions: 24*24*3 mm Weight: 3.4g Control via AT commands (GSM 07.07...

Reference: RBD-1253

Wuli bot Programmable Robot

1 review

Program Software: Mixly + XR Scratch(base on Scratch2.0) Input: Edge sensor, Button, IR receiver module, Ultrasonic sensor, Tracking sensor Output: Buzzer, RGBLED, Two motor port,OLED CPU: Arduino UNO R3 Power: 2Pcs 3.7V DC Lithium battery Control: WiFi control/IR remote

Reference: RBD-0260

Jumper Wire housing 5 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 5 jumper wires (5-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-0345

ESP8266 ESP-01 WIFI Wireless Transceiver Send Receive LWIP AP+STA M70

40 reviews

802.11 b/g/n Standards Wi-Fi Direct (P2P), soft-AP 1MB Flash Memory Integrated low power 32-bit CPU could be used as an application processor A-MPDU & A-MSDU aggregation & 0.4ms guard interval Wake up and transmit packets in < 2ms Standby power consumption of < 1.0mW (DTIM3) RoboticsBD

Reference: RBD-1129

Brand: RoboticsBD

Otto Bot Complete

1 review

Complete Assembled  Plug and Play Open Source Design Compatible With Arduino IDE DIY Kit

Reference: RBD-0262

Jumper Wire housing 6 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 6 jumper wires (6-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-1252

Makeblock mBot Ranger 3-in-1 educational robot kit

Tackle any terrain with Ranger’s 3 preset forms All-terrain Off-road Land Raider Super Speedy Dashing Raptor Self-balancing Nervous Bird EASY INSTALLATION: Build in as little as 45 minutes

Reference: RBD-1255

NodeMCU ESP8266 with 0.96 Inch OLED Module Development Board

5 reviews

Integrated 0.96″ OLED Micro USB connection Compatible with Arduino Compatible with NodeMCU(Lua for ESP8266) Input Power 5V Compatible for Arduino Compatible with NodeMCU(Lua for ESP8266)

Reference: RBD-0263

Jumper Wire housing 7 Pin

Tidy up your workspace and organize your jumper wires with this handy 3D printed housing for Dupont connectors. Securely holds up to 7 jumper wires (7-pin) for easy access and strain relief. No soldering required - simply snap the connector housings into place. Compatible with Arduino, Raspberry Pi, sensors, LED strips, and various DIY electronics projects.

Reference: RBD-1313

Lynxmotion Johnny 5 Combo Kit

Indoor and Outdoor Tracked Robot Platform Designed for indoor or outdoor use and performs well on many different surfaces Its a very cool and completely functional model of the ever popular movie robot