Reference: RBD-1354
Jumper Wire Single 20cm
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1354
Length: 8 inches/20 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-0351
Contactless transmission of data and supply energy (no battery needed) Operating distance: Up to 100mm (depending on antenna geometry) RoboticsBD Operating frequency: 13.56MHz Data transfer: 106 kbit/s Data integrity: 16 Bit CRC, parity, bit coding bit counting Anticollision Typical ticketing transaction: <100 ms ( including backup management)...
Reference: 0245
Choose your desire Resistor value from below:
Reference: 0031
3 Types Available (Please select from option) 1. Male to Male 2. Male to Female 3. Female-Female
Reference: RBD-0768
Size: 5mm Color: RED Head Shape: Round Lens Appearance: Transparent
Reference: RBD-0761
Breadboard friendly Mounting Style: Through Hole Mounting Direction: Vertical
Reference: 1353
Length: 12.5 inches/30 CM (Long) Material: Copper Plated Pin Spacing: 2.54mm.
Reference: RBD-1068
This is a DC Mini Metal Gear Motor, ideal for making robots Lightweight, high torque and low RPM. Fine craftsmanship, durable, not easy to wear. With excellent stall characteristics, can climb hills easily. You can also easily mount a wheel on the motor’s output shaft.
Reference: RBD-1175
Low-noise analog signal path Device bandwidth is set via the new FILTER pin 5 µs output rise time in response to step input current Small footprint, low-profile SOIC8 package 2.1 kVRMS minimum isolation voltage from pins 1-4 to pins 5-8 Supply Voltage: 4.5V~5.5V DC Measure Current Range: 20A Sensitivity: 100mV/A
Reference: RBD-1207
High-Quality Tracker Sensor The module is a convenient carrier for eight IR emitter and receiver pairs evenly paced. Distance between each IR Sensor: 15mm Uses 5 sensors for best resolution Great useful in building fast line following and grid navigating robots Comes with easy to use digital outputs with a direct connection to microcontrollers The array...
Reference: RBD-1220
LCD Thermometer and Humidity Measuring Extended Sensor Sampling Period 10Sec Long-Lasting Battery
Reference: RBD-1248
Speed(RPM):19000 Motor diameter: 6mm Shaft diameter: 0.8mm Shaft length: 4mm Rated voltage: 1.5V-3.1V
Reference: RBD-1570
Length: 9″. Pitch: 4.7″. Weight: 20 gm. Shaft Diameter: 7.86 mm. Total Length: 9 inch / 225 mm. Material: ABS
Reference: RBD-1677
Contact Rating: 10 W. Switching Voltage: 220 V. Switching Current: 0.5 A. Breakdown Voltage: 220 VDC. Carry Current: 1 A. Contact Resistance: 100 mΩ.
Reference: RBD-1852
IPEX To SMA Female External Antenna Adapter SMA Male Antenna for 2.4G WIFI Module Only Antenna and Adapter RF Cable ESP32 Cam is not included
Reference: RBD-2106
40P color jumper wires Length: 300mm Weight: 45 gm Compatible with 2.54mm spacing pin headers High quality and in good working condition Durable and reusable Easy to install and use
Reference: RBD-2259
Type: Hexagonal coupling. Material: brass. Inner diameter: 3 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 14.6gm
Reference: RBD-2511
Switching a lot of power? N-channel power MOSFET - 30V / 60A IRLB8721 MOSFETs are just what you need.These TO-220 package power MOSFETs can switch 30V/60A, which is plenty for most makers! They fit straight into a breadboard or even your own PCB with 2.54mm spaced pads.
Reference: RBD-0386
1 Hz output pin SQW. 32 KHz output pin 32K. RoboticsBD Voltage Supply: 2.2 V ~ 5.5 V (for RTC). Time Format: HH: MM: SS (12/24 hr). Date Format: YY-MM-DD-dd. DS 3231 based RTC with 2032 Battery Holder. RoboticsBD Battery is not included Note: Batteries not included.
Reference: RBD-0422
Dimensions: 210 x 17 mm(LxW) Weight: 8 gm. Fit for Fingerprint Scanner - TTL (GT-511C3) & Fingerprint Scanner - 5V TTL (GT-511C1R) Wire Sleeve material: Silicon. RoboticsBD
Reference: RBD-0424
SI7021 SHT21 HTV21 Wide operating voltage (1.9 to 3.6 V) – 3.3 V Recommended Precision Relative Humidity Sensor ± 3% RH (max), 0–80% RH High Accuracy Temperature Sensor ±0.4 °C (max), –10 to 85 °C Interchangeable - No recalibration required. RoboticsBD I2C Interface
Reference: RBD-0676
Operating voltage: DC 5 V. The analog output voltage, the higher the concentration the higher the voltage. The carbon monoxide detection with better sensitivity. With a long service life and reliable stability. Rapid response and recovery characteristics. Range: 10 to 1000 ppm. RoboticsBD
Reference: RBD-0949
Operating Voltage : 2.5 ~ 4V Operating Current : 130 ~ 220mA Flow Rate : 80 ~ 120 L/H Maximum Lift : 40 ~ 110 mm Outlet Outside Diameter: 7.5 mm Outlet Inside Diameter: 5 mm
Reference: RBD-1020
Frequency (MHz) : 824 – 960 MHz & 1710 – 1980 MHz Gain:2 / 3 dBi Impedance (Ω): 50 Connector Type: SMA Plug VSWR :< 2.5
Reference: RBD-1042
Operating Voltage: 3.3 ~ 5.5 VDC. Operating Current: 5mA. Interface: PH2.54-3P. Dimensions mm(LxWxH): 98 x 23 x 4. Supports 3-Pin Gravity Sensor interface Analog output. Weight (gm): 15.
Reference: RBD-1174
Low-noise analog signal path. Device bandwidth is set via the new FILTER pin. 5 µs output rise time in response to step input current. Small footprint, low-profile SOIC8 package. 2.1 kV RMS minimum isolation voltage from pins 1-4 to pins 5-8.
Reference: RBD-1249
Voltage Range: DC 2.5-4V. Motor Diameter: 10 mm. Motor Thickness: 3.4 mm. Min. Rated Speed: 9000RPM Max. Rated Current: 90mA
Reference: RBD-1413
Brand: Raspberry Pi Official
Material: ABS- 3 different cover board- Color: White & Red- Use For: Raspberry Pi Zero V1.3 and Raspberry Pi Zero W- Camera Cable Length: 37mm
Reference: RBD-1505
Input Voltage: 230V AC Output Voltage: 12V or 0V Output Current: 0.6 Amp Soft Iron Core. 0.6 Amp Current Drain.
Reference: RBD-1571
Length: 10″. Pitch: 4.5″. Weight: 25 gm. Shaft Diameter: 9.5 mm. Total Length: 10 inch / 250 mm. Material: ABS
Reference: RBD-2151
2-Axis joystick Bluetooth / Serial interface I2C interface nRF24L01 interface Nokia 5110 LCD interface Interface connector Power switch to switch between 3.3 and 5V
Reference: RBD-2230
Main chip: NE555 Input Voltage: 5V-15V DC. Generate an adjustable pulse for MCU. Generate an adjustable pulse, to control circuitry associated.
Reference: RBD-2260
Type: Hexagonal coupling. Material: brass. Inner diameter: 4 mm. Total length: 18 mm. Size of Hex Socket(Long Diagonal): 14mm Weight: 13.6gm
Reference: RBD-2574
This sturdy black bracket is made from 3mm-thick coated steel and weighs about 100g. It is specifically designed to work with the typical face plate mounting holes of NEMA 17 stepper motors.
Reference: RBD-0161
Model: LCD2004 Character Color: White Backlight: Blue Supply voltage: 5V Dimensions(L x W x H) mm: 98 x 60 x 12
Reference: RBD-0434
Supply Voltage: 8.2 – 42 VDC. Current Capacity : 2.2A max(24V). Continuous current per phase: 1.5 A. Minimum Logic voltage: 2.5V. Maximum Logic Voltage: 5V. Microstep resolutions: full, 1/2, 1/4, 1/8, 1/16, and 1/32. Dimensions : 15 x 20 mm. Weight: 4 gm. RoboticsBD
Reference: RBD-0658
Standard interface layout, compatible with a variety of Arduinos such as the Pro Mini Original FTDI FT232 chip, stable performance USB power has current protection, using 500MA self-restore fuse RXD/TXD transceiver communication indicator With power, sending, receiving indicator, working status LED indicators Mini USB Port Connection Support 3.3V, 5V...
Reference: RBD-0677
Using high-quality dual-panel design, with power indicator and TTL signal output instructions. The switching signal having a DO (TTL) output and analog output AO. TTL output valid signal is low. The higher the voltage, the concentration of the analog output voltage is higher. A hydrogen gas detection with good sensitivity. Has a long life and reliable...
Reference: 0828
Supported Motors: 10kg-cm servos (such as MG995, MG996) This product is made of high-quality materials and is durable. Various sensors can be installed to complete a variety of novel interactive works through the servo controller. It is convenient to install the camera, which can realize image monitoring and image recognition and tracking. Choose your...